微熱再生吸附式干燥機 微熱吸附式干燥機 微熱再生吸干機 吸干機

 






吸附式干燥機可分為三種:無熱再生吸附式干燥機，微熱再生吸附式干燥機和組合式干燥機。由于脫水原理的限制，冷凍式干燥機處理后的空氣壓力露點溫度只能達到：2--8℃，在一些空氣品質要求較高的場合，不能滿足用氣要求，只能使用吸附式干燥機和組合式干燥機。吸附式干燥機是根據變壓吸附原理，利用干燥機本身特有的微孔，通過毛細作用吸附空氣中的水分，利用自身及微熱再生方法對壓縮空氣進行吸附干燥，使其能達到露點溫度為-40--- - 70℃。

歡迎各界同仁來人來電咨詢、洽談!詳細資料至公司索取。我們將以一流的產品，合理的價格，優(yōu)質的服務與您密切合作，共謀發(fā)展！

      企業(yè)官網：www.senpull.cn      國內熱線：400-6969-728    技術咨詢：021-51602627       51602681

     【進口壓縮機國際亞洲配送中心】【中國空壓機備品備件營銷中心】

微熱再生吸附式壓縮空氣干燥機是一種利用多孔性固體物質（活性氧化鋁、13X分子篩）表面的分子力來吸取氣體中的水份，同時另一塔里利用壓力變化解吸氧化鋁所吸收的水分，從而獲得較低露點溫度、干燥、潔凈氣體的凈化設備.

 技術參數進氣溫度：≤50℃工作壓力為：0.6—1.0Ma壓力損失：≤0.02Ma

May be divided into three kinds: no heat regenerative adsorption dryer adsorption dryer, tepefaction regeneration adsorption dryer and combined type dryer. Due to the limitation of the dewatering principle, the air pressure dew point temperature of the freezing type dryer can only be reached: 2--8, in some cases, it can not meet the requirement of air quality. The adsorption type dryer is according to a pressure swing adsorption principle, use the dryer"s own unique microporous, through the water absorbed from the air by the capillary action by itself and tepefaction regeneration method of compressed air drying by adsorption the reaches the dew point temperature is -40---- 70 DEG C.

Welcome to come from all walks of life to inquire, negotiate. We will be first-class products, reasonable prices, quality service and your close cooperation, and seek common development!

Enterprise official website: www.senpull.cn domestic hot line: 400-6969-728 technical advice: 021-51602627 51602681

[imported compressorinternational asiadistribution center] [Chinese air compressor spare parts marketing center]

Tepefaction regeneration adsorption type compressed air dryer is a use of porous solids (activated alumina, 13X molecular sieve) surface of molecular force to absorb the moisture in the gas, and another tower using pressure desorption alumina absorbed moisture to obtain low dew point temperature, dry and clean air purification equipment.

Technical parameters: the inlet temperature is not higher than 50 DEG working pressure: 0.6 1.0Ma pressure loss: less than 0.02Ma