西門子進口NCU572.4

New NC functions in SW release 6.5

-

The previous software option - spline interpolation 6FC5251-0AA14-0AA0 was split-up as follows as a result of customer requests:
- spline interpolation for 5-axis machining 6FC5251-0AA14-0AA0
(functional scope, as before) and
- spline interpolation for 3-axis machining 6FC5251-0AF14-0AA0
This means, that a favorably-priced solution is available for customers who wish to implement a 3-axis machining application.

-

The option Path Length Evaluation 6FC5251-0AF05-0AA0 is used to detect the traversing distance/time (path length) for each axis, separately according to feed and rapid traverse and to sense the number of traversing operations as well as the number of jerks. This means that data is available that permits information to be provided about the maintenance condition of the machine via an external service (utility).

-

The unified nature of the NCU system software has been expanded over all hardware platforms with respect to SW 6.4:

A=axes, C=channel, 6(31) = 6 from 31 axes

New drive functions in SW release 6.5
The following have been newly included in the drive software 05.01.25 (for the Standard 1, Standard 2 and Performance 1 closed-loop controls) and 06.06.07 (for the High-Standard and High-Performance closed-loop controls):

-

Brake control and plausibility monitoring, encoder *)
*) Documentation: SIMODRIVE 611 digital SINUMERIK 840D/810D drive functions; Edition 02/2004

-

The option Advanced Positioning Control (APC) 6FC5251-0AF04-0AA0 allows a higher position controller gain (KV factor), an improved workpiece surface and therefore higher machine productivity. This has been made possible by actively damping the machine natural frequencies.
Prerequisite: The High-Performance control is used.
Note: The machine equipment may only be commissioned by Siemens A&D MC RD55

Extensive detailed improvements / the removal of software limitations with respect to V06.04.15; refer to the Upgrade Instructions

Loadable compile cycles (no change with respect to SW release 6.4; refer to 15093368

Order No.

Designation

For hardware

NCU system SW 6.5 V06.05.11 Export versions

6FC5250-6DY30-5AH_

NCU system software for 2 axes

NCU *.4 / 573.5

6FC5250-6CY30-5AH_

NCU system software for 6 axes

NCU *.4 / 573.5

6FC5250-6BY30-5AH_

NCU system software for 12 axes

NCU 572.3/573.3; NCU *.4 / 573.5

6FC5250-6AY30-5AH_

NCU system software for 31 axes

NCU 572.3/573.3; NCU *.4 / 573.5

NCU system SW 6.5 V06.05.11 standard versions

6FC5250-6CX30-5AH_

NCU system software for 6 axes

NCU *.4 / 573.5

6FC5250-6BX30-5AH_

NCU system software for 12 axes

NCU 572.3/ 573.3; NCU *.4 / 573.5

6FC5250-6AX30-5AH_

NCU system software for 31 axes

NCU 572.3/ 573.3; NCU *.4 / 573.5

Last position of the Order No. [MLFB]:
_ = 0 : Single license
_ = 3 : Update

NCU software options

6FC5251-0AF14-0AA0

Spline interpolation for 3-axis machining

All NCU with the exception of NCU561.4

6FC5251-0AF05-0AA0

Path Length Evaluation

All NCU

6FC5251-0AF04-0AA0

Advanced Positioning Control (APC)

All NCU with the exception of NCU561.4

Notes:

-

NCU *.4: NCU 561.4 / 571.4 / 572.4 / 573.4

-

The release for general availability ex-factory will be from the middle of March 2004

-

The software is, effective immediately, electronically available (eSupport; if you have a requirements, please contact your local Siemens office)

-

From the middle of March 2004, updates 06.05.11 will be supplied for software update contracts.

-

Orders for "Actual SW release" will still be substituted for "Basic license" SW 6.4.

-

The versions 06.05.05, 06.05.06 and 06.05.08, made available for machine tests with pilot release and exclusion of liability, should, immediately be replaced by the released V06.05.11

NCU system software
6FC5250-.....-5AH_


on NCU

-6AX30-
-6AY30-
-6BX30-
-6BY30-

-6A_30-
-6B_30-
-6C_30-
-6DY30-

-6A_30-
-6B_30-
-6C_30-
-6DY30-

572.3*)
573.3

561.4
571.4
572.4
573.4

573.5

Operator components
/software

SW
release

MMC100.2

5.3

X

X

-

HMI Embedded

6.2
6.3

X
X

X
X

-
X

OP 030

4.2

X

X

X

HPU

5.1

X

X

-

HT 6 ¹⁾

6.1
6.4

X
X

X
X

X
X

MMC 103

5.3

X

X

-

Start-up tool

6.2
6.3

X
X

X
X

-
X

HMI Advanced

6.1
6.2
6.3

X
X
X

X
X
X

-
-
X

Basic PLC
program

6.3
6.4
6.5

X
X
X

X
X
X

-
-
X

Explanation of characters:

X

compatible

-

not compatible

1)

FC26 >=5.03.04 download from the toolbox!

*

not tested

-

The function G643 "Internal block approximate positioning" has been released for applications in the tool change area (e.g. optimized approach to the tool change position). It has not been released for applications in the machining process.

-

The FCUB, FLIN functions in conjunction with the compressor COMPCAD have not been released.

-

NCU *.3: It is only permissible to run-down the PCU 50 using the EXIT button in the Emergency Off state.

-

NCU *.4: It is only permissible to run-down the PCU 50 using the EXIT button in the Emergency Off state - if a PLC operating system <10.60.17 is used.

-

The many new and expanded functions in SW release 6 require more memory space / performance and therefore result in the following system dependencies for older NCUs:

--

NCU system SW 31 axes only enabled for 6 channels:
NCU 572.3 (6FC5357-0BB22-0AE0)
NCU 572.4 (6FC5357-0BB23-0AE0)

--

NCU system SW 31 axes only enabled for 8 channels:
NCU 573.3 (6FC5357-0BB33-0AE2)

-

Update 2004-06-02:
Update 2004-04-06:
"Safety Integrated" in combination with the NCU 573.5 has not been  released for tests.

-

Update 2004-04-06:
The function "M to N" has not been released in combination with the NCU 573.5.

-

Update 2004-04-06:
The function "NCU link" has not been released in combination with the NCU 573.5.

-

ERLde65040:
Incompatible spindle behavior between SW6.3 and SW6.4 for HIFU groups
with $MC_AUXFU_ASSIGN_VALUE=-1
SW6.3: M2=3 S2=100-->spindle 2 rotates and M3 is output in the axis DB.
SW6.4: M2=3 S2=100-->spindle 2 does not rotate and M3 is not output in the axis DB.

-

ERLde65276:
With $MN_FRAME_GEOAX_CHANGE_MODE =2, for transmit, the zero offset of the rotary axis is deleted.

-

ERLde65174:
Cutting_Edge_Default=0 does not work for Tool_Change_Error_Mode=1. This means after M6, the previous correction is not de-selected.
Remedy: Program D0 before the next traversing block

Additional system interdependencies / limitations: Refer to the commissioning and start-up instructions.