|
牌號
|
X6CrNiTi12不銹鋼板和鋼帶
|
|
|
|
|
|
|
|
|
|
|
1.4516
|
|
|
|
|
|
|
|
|
|
對應標準
|
NF EN 10088-2-2005
|
|
|
|
|
|
|
|
|
|
普通用途不銹鋼板和鋼帶的交貨技術條件
|
|
|
|
|
|
|
|
|
|
Part2:Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
|
|
|
|
|
|
|
|
|
|
歸類
|
鐵素體不銹鋼
|
|
|
|
|
|
|
|
|
|
標簽
|
標準等級
|
|
|
|
|
|
|
|
|
|
X6CrNiTi12 化學元素成分含量(%)
|
|
|
|
|
|
|
|
|
|
|
成分
|
C
|
Si
|
Mn
|
P
|
S
|
Cr
|
Ni
|
Ti
|
|
|
最小值
|
-
|
-
|
-
|
-
|
-
|
10.5
|
0.5
|
0.05
|
|
|
最DA值
|
0.08
|
0.7
|
1.5
|
0.04
|
0.015
|
12.5
|
1.5
|
0.35
|
|
|
◎ 未經買方同意，不得隨意向鋼中添加表中未列的元素，冶煉精加工除外。采取一切必要措施以防在廢鋼和生產原料中帶入這些元素，因為其會削弱鋼的機械性能，降低鋼的適用性。
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
X6CrNiTi12 機械性能
|
|
|
|
|
|
|
|
|
|
|
條件
|
熱處理或狀態
|
抗拉強度
|
屈服點
|
斷后伸長率或延伸率
|
|
|
|
|
|
|
σb
|
σs
|
δ
|
|
|
|
|
|
|
Mpa
|
Mpa
|
%
|
|
|
|
|
|
|
冷軋帶鋼：T ≤ 8mm
|
+A
|
450~650
|
l：≥280；t：≥320
|
≥ 23①
|
|
|
|
|
|
|
熱軋帶鋼：T ≤ 13.5mm
|
+A
|
450~650
|
l：≥280；t：≥320
|
≥ 23①
|
|
|
|
|
|
|
熱軋中厚板：T ≤ 25mm ②
|
+A
|
450~650
|
l：≥250；t：≥280
|
≥ 20①
|
|
|
|
|
|
|
◎ T-厚度；l-縱向; t-橫向
|
|
|
|
|
|
|
|
|
|
|
◎ +A=軟化退火；+QT=淬火及回火；+P=沉淀硬化；+AT=固溶退火；+SR=消除應力
|
|
|
|
|
|
|
|
|
|
|
① T＜3mm時適用于標距為80mm、寬度為20mm的試件。也可以使用標距為50mm、寬度為12.5mm的試件。T ≥3mm時適用于標距為5.65√S的試件。
|
|
|
|
|
|
|
|
|
|
|
② T＞25mm時，力學性能可以商定。
|
|
|
|
|
|
|
|
|
|
|
* 交貨條件下無抗晶間腐蝕; 焊接狀態下無抗晶間腐蝕（根據EN ISO 3651-2進行測試）。
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
交付條件下在高溫下的最小屈服強度
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Material designation
|
Heat treatment
|
Minimum 0.2%-proof strength,MPa
|
|
condition
|
at a temperature (in°C) of:
|
|
Name
|
Number
|
|
100
|
150
|
200
|
250
|
300
|
350
|
400
|
|
X6CrNiTi12
|
1.4516
|
+A
|
300
|
270
|
250
|
245
|
225
|
215
|
-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
符合本歐洲標準的產品熱處理指南
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Material designation
|
Hot forming
|
Heat treatment
|
Annealing
|
|
|
|
|
Name
|
Number
|
Temperature
|
Type of
|
symbol
|
Temperature
|
Type of
|
|
|
|
|
℃
|
cooling
|
|
℃ ①
|
cooling
|
|
|
|
|
X6CrNiTi12
|
1.4516
|
1100 to 800
|
air
|
+A
|
790 to 850
|
air,water
|
|
|
|
|
◎ Temperature of annealing shall be agreed for simulated heat-treated test-pieces.
|
|
|
|
|
① If heat-treatment is carried out in a continuous furnace, the upper part of the range specified is usually preferred, or even exceeded.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
