TOP-3MF2200-N340FA AC200V 進口福州錦菲特NOP擺線泵

---福州錦菲特自動化設備-宋先生v信18950268848---

1ME200-11MA
1ME200B-13KAVB
1ME200-12MA
1ME75-1-11MA
1ME75-2-12MA
1ME75-2-11MA
1ME200-10MAVB
1ME100-13MA
1ME75-2-10MA
1ME200-13MAVB
1ME75-1-12MAVB
1ME75-1-10MA
1ME200-13MAVB
1ME100-13MAVB
1ME200A-12KAVB
1ME200-12MAVB
1ME200-13MA
1ME100
1ME100-11MAVB
1ME200-10MA
1ME200B-12KAVB
1ME75-2-10MAVB
1ME200
1ME200-11MAVB
1ME100-12MA
1ME100-11MA
1ME200S-12MAVB
1ME75-2-12MAVB
1ME75-1-11MAVB
1ME75-1-10MAVB
1ME100-10MA
1ME200D-13KAVB
1ME100-12MAVB
1ME75-1-12MA
1ME100-10MAVB
1ME75-2-11MAVB 注意事項
(1)如發現擺線齒輪泵有異常聲音應立即停車檢查原因 (2)向擺線齒輪泵軸承體內加入軸承潤滑機油,觀察油位應在油標的中心線處,潤滑油應及時更換或補充. (3)擰下擺線齒輪泵泵體的引水螺塞,灌注引水(或引漿). (4)關好擺線齒輪泵出水管路的閘閥和出口壓力表及進口真空表. (5)點動擺線齒輪泵電機,試看電機轉向是否正確. (6)開動擺線齒輪泵電機,當擺線齒輪泵正常運轉后,打開出口壓力表和進口真空泵,視其顯示出適當壓力后,逐漸打開閘閥,同時檢查電機負荷情況. (7)擺線齒輪泵長期停用,需將擺線齒輪泵全部拆開,擦干水分,將轉動部位及結合處涂以油脂裝好,妥善保存. (8)擺線齒輪泵在運行過程中,軸承溫度不能超過環境溫度35C,溫度不得超過80C . (9)檢查擺線齒輪泵及管路及結合處有無松動現象.用手轉動擺線齒輪泵,試看擺線齒輪泵是否靈活.. (10)擺線齒輪泵要停止使用時,先關閉閘閥,壓力表,然后停止電機. (11)擺線齒輪泵在工作個月內,經100小時更換潤滑油,以后每個500小時,換油一次. (12)經常調整擺線齒輪泵填料壓蓋,保證填料室內的滴漏情況正常(以成滴漏出為宜). (13)定期檢查擺線齒輪泵軸套的磨損情況,磨損較大后應及時更換. 擺線齒輪泵的結構特點 在輸油系統中可作傳輸、增壓泵。