- 產品
- 供應
- 公司
- 新聞
|
|
||||||||||||||||||||||||||||
AN9634H交直流耐壓測試儀@AN9634H%
| 主要特點： |
■ 滿足IEC60335、UL60335、GB4706.1-2005、GB4943等國內外安規標準測試，符合JJG795-2004、JJG690-2003安規計量檢定規程要求；
■ 電氣強度安全檢測的綜合解決方案；
■ 大屏幕LCD顯示，中英文雙語界面；
■ 緩升緩降、掃描測試、測線歸零功能；
■ 上下限報警設置，開路、短路保護功能；
■ 智能判別，聲光報警，大字符顯示；
■ 8組*8步條件設置記憶和呼出功能；
■ 先進的PWM控制技術和DSP技術；
■ 三個項目測試最快2.5S的高速檢測；
■ 高精度、高效率、大容量、小體積。
| 適用對象： |
交流耐壓輸出5000VAC/100mA（持續時間30分鐘），直流耐壓輸出6000VDC/10mA（持續時間30分鐘），能快速準確的完成上述性能指標的測試，能滿足各電器、元器件生產廠家和質檢部門依照國際和國家安規標準進行上述安全性能檢測的要求。
|
技術參數： |
|
技術參數
|
AN9634H
交流耐壓、直流耐壓二合一
|
|
|
交
流
耐
壓
測
試
|
輸出電壓設定和測量范圍
|
100V～5000V AC 100mA 1V/步
|
|
輸出電壓調整率
|
±（2%×設定值+5V）
|
|
|
輸出電壓分辨率及精度
|
10V ±（2%×設定值+5V）
|
|
|
輸出頻率范圍及精度
|
50Hz/ 60Hz ±100ppM
|
|
|
輸出波形
|
正弦波 純阻負載下,200V以上失真度優于2%,100V～200V優于5%
|
|
|
擊穿電流報警上下限設定
|
上限0.00～99.99mA 0.001mA/步；
下限0.000～9.999mA 0.001mA/步
|
|
|
擊穿電流測量范圍
|
0.000～3.500mA/ 3.50～99.99mA
|
|
|
擊穿電流測量分辨率
|
0.001mA/0.01mA
|
|
|
擊穿電流測量精度
|
0.2mA以上優于±（2%×顯示值+3個字）；
0.2mA 以下優于±（2%×顯示值+10個字）
|
|
|
緩升/緩降/測試時間范圍
|
0.0～999.9s/ 0.0～999.9s/ 0.5～999.9s 0.1s/步
|
|
|
測線歸零
|
0～2.000mA,自動或手動消除空載時的偏差值
|
|
|
直流耐壓測試
|
輸出電壓設定和測量范圍
|
100V～6000V DC 10mA 1V/步
|
|
輸出電壓調整率
|
±（2%×設定值+5V）
|
|
|
輸出電壓分辨率及精度
|
10V ±（2%×設定值+5V）
|
|
|
直流電壓紋波系數
|
≤5%（在6kV,<1mA電流純阻性負載條件下測試）
|
|
|
擊穿電流報警上下限設定
|
上限0～9999uA 1uA/步；下限0.0～999.9uA 0.1uA/步
|
|
|
直流緩升電流上限設定范圍
|
12mA ON或OFF可設置
|
|
|
直流充電電流下限設定范圍
|
0.0～350.0uA
|
|
|
擊穿電流測量范圍
|
0.0～350.0uA/ 300～3500uA/ 3.00～9.99mA
|
|
|
擊穿電流測量分辨率
|
0.1uA/1uA/0.01mA
|
|
|
擊穿電流測量精度
|
0.0～350.0uA: ±（2%×設定值+5個字）;
350.0～9999.0uA: ±（2%×設定值+2個字）
|
|
|
緩升時間設定/測試時間范圍
|
0.0～999.9s/ 0.5～999.9s 0.1s/步
|
|
|
測試歸零
|
0～200uA, 自動或手動消除空載時的偏差值
|
|
|
功能接口
|
開關量接口：啟動、停止信號輸入、調用1-8組，合格、報警、測試、故障信號輸出；掃描口、RS232(RS485)和打印口
|
|
|
外形尺寸W×H×D(mm)
|
400×156×475
|
|
|
儀器配件： |
|
配件名
|
型號
|
|
接地線
|
AN000-03
|
|
測試線
|
AN960-02
|
|
測試探棒
|
AN960-01
|
AN9634H AC and DC withstand voltage tester@AN9634H%
Main features:
■ IEC60335, UL60335, GB4706.1-2005 content, GB4943 and other domestic and international safety standard test,with JJG795-2004, JJG690-2003 safety rules of metrological verification requirements;
A comprehensive solution ■ electrical strength safetydetection;
■ LCD screen display, in English bilingual interface;
■ slow rise and slow drop, scan test, line zero function;
■ alarm settings, open circuit, short circuit protection function;
■ intelligent identification, sound and light alarm, large character display;
■ 8 groups of *8 step condition setting memory and call out function;
■ advanced PWM control technology and DSPtechnology;
High speed detection ■ three project to test the fastest2.5S;
■ high precision, high efficiency, large capacity, smallvolume.
Applicable objects:
AC voltage output 5000VAC/100mA (duration 30 min), the DC voltage output 6000VDC/10mA (duration 30 min), can quickly and accurately complete the performance testing,can meet the all electric components manufacturers, andquality inspection departments in accordance with theinternational and national safety standards for the safety testing requirements.
Technical parameters:
Technical parameters of AN9634H
AC voltage, DC voltage in
Hand in
Flow
Resistance to
Pressure
Test
Try to set the output voltage and the measurement range from 100V to 5000V AC 100mA 1V/
Output voltage regulation rate ± (2% × set value +5V)
The output voltage of the resolution and precision of 10V+ (2% x the set value +5V)
The output frequency range and precision of 50Hz/ 60Hz+ 100ppM
Sine wave output waveform pure resistance load, 200Vdistortion is better than 2%, 100V ~ 200V is better than 5%
The breakdown current alarm limits set the upper limit of 0 ~ 99.99mA 0.001mA/;
The lower limit of 0 ~ 9.999mA 0.001mA/
The breakdown current measurement range of 0 ~ 3.500mA/, 3.50 ~ 99.99mA
The breakdown current measurement resolution of 0.001mA/0.01mA
The breakdown current measurement accuracy is better than ± (2% × 0.2mA above the display value of +3 words);
0.2mA is better than ± (2% × display value of +10 words)
The slow rise / fall / test time range of 0 ~ 999.9s/, 0 ~999.9s/, 0.5 ~ 999.9s 0.1s/
The line of zero 0 ~ 2.000mA, automatic or manual toeliminate the deviation of no-load value
DC withstand voltage test output voltage setting and measurement range of 100V to 6000V DC 10mA 1V/
Output voltage regulation rate ± (2% × set value +5V)
The output voltage of the resolution and precision of 10V+ (2% x the set value +5V)
DC voltage ripple ≤ 5% (in 6kV, <1mA current pure resistive load conditions test)
The breakdown current alarm limits set the upper limit of 0 ~ 9999uA 1uA/ step; the lower limit of 0 ~ 999.9uA0.1uA/
DC slow rise and current limit set the range of 12mA ON or OFF can be set
DC charging current limit setting range 0 ~ 350.0uA
The breakdown current measurement range of 0 ~ 350.0uA/, 300 ~ 3500uA/, 3 ~ 9.99mA
The breakdown current measurement resolution of 0.1uA/1uA/0.01mA
The breakdown current measurement precision 0 350.0uA: ± (2% × set value +5 words);
350 - 9999.0uA: + (2% x the set value +2 words)
The slow rise time set / test time range of 0 ~ 999.9s/, 0.5 ~ 999.9s 0.1s/
The test of zero 0 ~ 200uA, automatic or manual toeliminate the deviation of no-load value
Interface switch interface: start, stop signal input, call 1-8group, qualified, alarm, test, fault signal output; scan port,RS232 (RS485) and print port
Dimensions of W × H × D (mm) 400 x 156 x 475
Instrument accessories:
Parts name type
Ground AN000-03
Test line AN960-02
Probe AN960-01
