重慶永川全自動掛歷單/雙線圈裝訂機 廠家電話價格報價

重慶市 江北區  渝北區  沙坪壩區  九龍坡區  萬州區  永川市  南岸區  酉陽縣  北碚區  涪陵區  秀山縣  巴南區  渝中區  石柱縣  忠縣  合川市  大渡口區  開縣  長壽區  榮昌縣  云陽縣  梁平縣  潼南縣  江津市  彭水縣  璧山縣  綦江縣  大足縣  黔江區  巫溪縣  巫山縣  墊江縣  豐都縣  武隆縣  萬盛區  銅梁縣  南川市  奉節縣  雙橋區  城口縣

全自動臺歷 掛歷 筆記本單/雙線圈裝訂機可能出現的異常、故障及排除方法 Trouble shooting

8.1 全自動臺歷 掛歷 筆記本單/雙線圈裝訂機沖孔系統故障排除 Punching system trouble shooting

   8.1.1   故障現象：機器不動 Symptom: The machine does not move
           產生原因：電源沒有接通或者保護開關觸發異常。

Cause: The power supply is not turned on or the protection switch is triggered
  排除方法：查看電源開關是否已經接通，保護開關有無異常， 配電箱內空氣開關是否斷開。

Remedy: Check whether the power switch is switched on, whether the protection switch is abnormal or not, and the air switch in the distribution box is disconnected
8.1.2異常現象：全自動臺歷 掛歷 筆記本單/雙線圈裝訂機毛邊大

Abnormal phenomenon: big hair
  產生原因：紙張太厚，沖針嚴重磨損

Cause: The paper is too thick and the punch is severely worn
  排除方法：正常運行紙張厚度建議在1-6mm之內；如果是沖針磨損嚴重請更換。Remedy: normal operation of the paper thickness is recommended within 1-6mm; if the pins wear, please replace.

8.2 全自動臺歷 掛歷 筆記本單/雙線圈裝訂機機器手送料系統的故障排除 The feed belt system trouble shooting

   8.2.1 故障現象：機器不動Symptom: The machine does not move
         產生原因：電源沒有接通或者光電開關觸發異常。Cause: The power supply is not turned on or the photoelectric switch triggers an abnormality
         排除方法：查看電源開關是否已經接通，光電開關有無異常。Remedy: Check whether the power switch is turned on, the photoelectric switch is abnormal.

   8.2.2  異常現象：全自動臺歷 掛歷 筆記本單/雙線圈裝訂機機械手抓取和送料位置不對             Abnormal phenomenon: the robot grab and feeding position is wrong

   產生原因：皮帶拉長松弛或者是皮帶固定塊1不牢靠。        Cause: The belt is stretched or the belt is fixed

   排除方法：將皮帶張緊到合適的松緊度，調整好機械手的位置鎖緊皮帶固定塊。Remedy: Tighten the belt to the appropriate tightness, adjust the position of the robot to lock the belt fixed block.