- 產品
- 供應
- 公司
- 新聞
|
|
||||||||||||||||||||||||||||
陜西省 西安市 咸陽市 寶雞市 漢中市 渭南市 安康市 榆林市 商洛市 延安市 銅川市
5.2.3 keep inching to find out limiting point (the highest point of paper patting roller) of paper patting equipment
注意：在紙張尺寸穩定的基礎上，將前后左右拍紙板調至剛好與紙張接觸無間隙效果最好，注意頁邊距和對稱度會很穩定。
Attention: on the basic of stable paper size, adjust four sides paper patting board to the gapless position to the paper. Then it will bring best effective and the page margins and symmetry will be much stable.
紙張厚度薄和硬度低時降低主機速度有利于沖孔精度的穩定。
It’s good for stable punching precisions to slow down machine speed when paper is thin or with low hardness.
5.3臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機沖孔模具的裝拆、抽針和紙邊距調整
install/dismantle/drawn needle/adjust paper margins the punching mould
5.3.1模具的拆卸和安裝：install/dismantle moulds
機器出廠時已經配備一套沖孔模具，如果需要更換請按照下面圖示步驟進行
Machine delivered with one punching mould. Please follow steps showed in the below picture if needs to change mould.
操作時需要配備適合M8及M16內六角螺釘?shù)陌馐郑@些扳手是隨機工具。
Spanner fitted model M8/M16 inner hexagon screw is necessary while changing moulds. The spanner is attached tools.
注意：安裝完畢所有螺釘都要緊固以防設備運轉時松動。
Attention: must fastening all screws after installation in case that machine runs not stably.
5.3.2臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機紙邊距的調整 adjust paper margins
模具安裝后電動完成一次沖裁，測量紙邊距，如不符合要求則進行下面的調節：
Finish one electrical blanking after installing mould to measure paper margins. If the result is not match requirements, please adjust as follows:
紙張距調整好就可以精調拍紙器的前后左右位置，至直沖孔符合要求。
Accurately adjust four sides position of paper patter after adjustment of paper margins until it matches punching requirements.
紙邊距設計最小2mm，最大5mm。min. paper margin: 2mm; max. paper margin: 5mm
5.4臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機沖封面的調整 adjustment of punching cover
5.4.1送紙轉換開關撥到“封面”位置，真空泵便會自動工作。
Switch paper feeding bottom to the “cover” position, and vacuum pump will work automatically.
5.4.2按點動按鈕上升到封面限位高度，如果封面太低、吸嘴吸不到，就調節限位
開關往上，使吸嘴能夠吸到位置，也可調節吸嘴高低旋鈕。
Press down inching bottom to lift to the high-limiting position. If the cover is too low to absorb it, adjust the limiting position or suction nozzle position to absorb the cover.
5.4.3封面高度調好后，再調節分紙片高度，使分紙片壓到上面一張封面。
Adjust paper separating height after adjustment of cover height to let the separating paper press on the above cover.
5.4.4注意“封面”吸嘴不能調節太高，以免碰到叼嘴尼龍塊，進“封面”不順暢。
Please note that not to adjust the cover suction nuzzle too high to touch taking nuzzle nylon, so that it’s not smooth to feed the cover.
5.4.5分紙片是用來控制紙張，應調整到適當位置，否則會出現吸不上封面或不起
作用。臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機
