- 產品
- 供應
- 公司
- 新聞
|
|
||||||||||||||||||||||||||||
陜西省 西安市 咸陽市 寶雞市 漢中市 渭南市 安康市 榆林市 商洛市 延安市 銅川市
開關閉合時，“封面”自動上升到適當位置。
Cover limiting switch is to limit lifting height automatically. Cover will be lifted to highest position if cover limiting switch is off.
臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機沖“封面”時，觸摸屏上紙張厚度設定就不起作用了，是由“封面”限位開
關來控制上升量。
The setting of paper thickness on the touch screen will not work when punching cover. It’s controlled by cover limiting switch.
臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機運行注意事項 running attentions：
運行中不要將手放在運動部件如模具等區域。
Don’t put hands into running sections such as moulds when machine is running.
觀察皮帶有無松脫現象。
Observe if belt get loose or not.
注意碎紙抽屜內紙屑不要過多溢出，以免紙屑堵住出口。
Note that waste paper in the drawer can’t be too much to overflow and stem the exit.
確保各個保護開關不受損移位。
Make sure that all the protection switches are not damaged.
不要長時間大厚度工作，這樣會造成沖針及模具過快磨損。
Not work under big thickness situation for long time. It will wear punching needle and moulds too fast.
臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機 故障排除 Stoppage remove
6.1 故障現象：臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機機器不動
產生原因：電源沒有接通或者保護開關觸發
排除方法：查看電源開關是否已經接通，保護開關有無異常， 配
電箱內空氣開關是否斷開
Stoppage: machine not runs
Reason: power off or protection switch is touched off.
Remove methods: check if the power switch is on, or if protection switch is normal, or if air switch in the electric box if off.
6.2 故障現象：臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機沖孔紙邊距不穩定，不對稱。
產生原因：拍紙器及擋紙板未固定牢固或與紙張間隙太大。
排除方法：調整緊固。
Stoppage: paper margins are not stable or symmetrical.
Reason: paper patter and paper board are not stable, or the distance from paper is too much.
Remove methods: fasten above mentioned parts.
6.3 故障現象：臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機毛邊大
產生原因：紙張?zhí)瘢瑳_針嚴重磨損
排除方法：正常運行紙張厚度建議在1.2mm之內；如果是沖針磨損嚴重請更換。
Stoppage: big deckle edge
Reason: paper is too thick or punching needle is heave wear.
Remove methods: suggest to work less than 1.2mm. please change punching needle if is heavy wear
6.4 故障現象：臺歷單/雙線圈裝訂機 掛歷單/雙線圈裝訂機 筆記本單/雙線圈裝訂機紙張不能順利進出模具
產生原因：A.不銹鋼導紙板與紙張距離過大或壓的太緊，不利于紙張順利出入模具。B.紙邊距擋紙板與模具過緊或過松，特別是更換模具時由于安裝及制造的差異有時會造成動作不靈活。
排除方法：調整不銹鋼紙板或紙邊距擋紙板位置。
Stoppage: it’s difficult to run in or out the mould
Reason: A. the distance between stainless steel paper feeding board and paper is too big or pressed too strict. B. the distance between paper margin board and mould is too big or pressed too strict. Especially the differences caused by installing the mould will lead to not smooth.
Remove methods: adjust stainless steel and margin paper board position.
