礦用FDJ-120風動切割鋸

FDJ-120型礦用乳化液切割鋸，是一款手持式切割鋸，以壓縮空氣為動力，小巧輕便，切割過程不發熱，不會才生火花。 FDJ型礦用乳化液切割鋸優點： 1、90度直切，45度斜切,立式切割一體機。 2、運轉速度只有砂輪機的1/60,安全無火花。 3、切縫窄0.5mm,切割表面平整，精度高，無掛渣，無脫碳。 4、鋸條使用壽命長，單位切割成本低，一根鋸條使用壽命等同于50-80片砂輪切割片，較電能鋸節能60%。技術參數： 項目 單位 性能參數 額定壓力 MPa 10 額定流量 L/min 30 切割速度 m/min 60 馬達空載轉速 R/min 1500 噪音 Db(A） ≤92 Db(A） ≤108 外形尺寸（長*寬*高） mm （200*500*190）±20 機重 kg 11 沖洗液壓力 MPa 3.0-4 有效切割寬度 mm 120*140

使用方法： 1、了解所需切割的材料，如有必要可以通過降低乳化液壓力來降低鋸片的轉動速度。 2、確保牢固固定了所需切割的材料，防止其移動。 3、轉動乳化液馬達時，用手指按壓閥桿，然后開始切割。 4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。） 5、關閉乳化液馬達時，釋放閥桿。 6、下次切割開始前，鋸片必須保持運動狀態。乳化液鋸時，鋸片不能接觸任何表面。 7、斷開乳化液軟管時，關閉乳化液軟管閥。斷開前，先打開乳化液閥給軟管減壓。 8、更換鋸片前，務必斷開乳化液軟管，并推動閥桿以釋放掉馬達內的壓力。 9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。

錨桿切割鋸是在煤礦巷道掘進支護、修巷時,用于修整錨桿長度的一種支護工具,它可安全快速地切斷直徑24 mm以下的高強度錨桿；此外,它還解決了進風區、老塘、采空區、回風區、落山角的頂板快速放頂問題,使瓦斯、煤塵積存量縮小,預防了瓦..斯、煤塵積存的隱患。 切割材料及適用范圍：（手持式防爆切割鋸主要應用煤礦井下、高瓦斯礦井、石油管道、天然氣管道、電纜等切割，要求切割過程不允許產生火花） 鐵管、鋼筋、電纜、銅管、鐵棒、銅棒、錨桿、錨索、鋼筋網、工字鋼、槽鋼、U型鋼、H鋼、角鋼、礦工鋼、軌道鋼、C型鋼。

 The FDJ-120 type mining emulsion cutting saw is a hand-held cutting saw, which is driven by compressed air. It's small and light. It doesn't generate heat when cutting. It doesn't generate sparks. FDJ type mine emulsion cutting saw advantages: 1, 90 degrees 45 degrees straight, oblique, vertical cutting machine. 2, the speed of operation is only 1/60 of sand turbine, and it is safe and free of spark. 3, the cutting seam is narrow 0.5mm, the cutting surface is smooth, the precision is high, no slag, no decarburization. 4, the sawing lifespan is long, the unit cutting cost is low, the service life of a sawing is equal to 50-80 pieces of grinding wheel cutting plate, and the electric saw energy sawing is 60%. Technical parameters: the project unit performance parameters of rated pressure of MPa 10 L/min 30 m/min rated flow cutting speed 60 motor no-load speed 1500 R/min noise Db (A) = 92 Db (A) is less than or equal to 108 dimensions (length * width * height) mm (200*500*190) + 20 kg 11 heavy machine washing fluid pressure MPa 3.0-4 effective cutting width mm 120*140
How to use: 1, understand the material needed to cut, if necessary to reduce the pressure of the emulsion to reduce the speed of the saw blade rotation. 2, ensure that the required cutting material is firmly fixed to prevent its movement. 3. When the emulsion motor is rotated, the stem is pressed with the finger and then the cutting is started. 4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity. 5. When the emulsion motor is closed, the stem is released. 6. The saw blade must remain moving before the next cutting begins. When the emulsion saw, the saw blade was not exposed to any surface. 7. When the emulsion hose is disconnected, the emulsion hose valve is closed. Before disconnecting, open the emulsion valve and decompress the hose. 8. Before replacing the saw, be sure to disconnect the emulsion hose and push the stem to release Madane's pressure. 9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod
Bolt cutting saw is in mine roadway, the roadway repair, used to trim the length of anchor a supporting tool, it can be safely and quickly cut off the high strength bolt diameter of 24 below mm; in addition, it also solves the problem of air inlet area, goaf, goaf, air return area, fast falling roof the top problem mountain angle, the accumulation of gas and coal dust emissions reduced, preventing the accumulation of coal dust, tile, hidden. The cutting material and the applicable scope: (portable explosion-proof cutting saw is mainly used in underground coal mine, high gas mine, oil pipelines, gas pipelines, cables and other requirements of cutting, cutting process is not allowed to produce sparks) pipe, steel, copper, iron, copper, cable, anchor, steel mesh, I-beam, channel steel, U H steel, steel, steel, steel, steel, coal miners C steel rail.