- 產品
- 供應
- 公司
- 新聞
|
|
||||||||||||||||||||||||||||
煤礦用防爆切割鋸 風動手持式切割機/鋸 各種鋼材切割鋸 防爆無火花切割鋸 多功能便攜式切割鋸 煤礦井下手持式切軌鋸 切管鋸 高瓦斯礦井專用切割鋸/機 煤礦井下快速切管機
管道、電纜、角鋼、結構鋼、U型鋼、鏈條、錨桿、錨索手持式氣動切割鋸 生產廠家 報價型號 性能 價格
風動手持切割鋸是我公司針對高危，安全系數要求特別高的工作環境，如化工.治煉廠.天然氣開采.高危潮濕的隧道，水下及狹窄的空間作業，尤其是高瓦斯防爆礦井。山西萬澤錦達礦山機械設備有限公司自主研發的新型多用途風動手持切割工具。它使用臺灣進口氣動馬達作為動力輸出，利用壓縮空氣作為動力源，不用電源。風動手持切割鋸不但整機重量輕，操作簡單，攜帶方便零火花，提高工作效益。本產品安全可靠是高危行業的最理想氣動切割工具。
一．技術參數:1適用材料:不銹鋼.鋁，銅.鉻合金，鎳基合金，玻璃，纖維，木材，塑料，鋼絲繩等。2切割范圍：120mm*120mm圓型材料，220mm*120mm方型材料。3工作壓力：0.3—0.8Mpa4外型尺寸：650*210*270
二．礦用軌道輕型3分鐘軌道重型5分鐘
三.優點1.90°直切,45°斜切,立式切割一體機。2.運轉速度只有砂輪機的1/60,安全無火花。3.切縫窄0.5mm,切割表面平整，精度高，無掛渣，無脫碳。4.鋸條使用壽命長，單位切割成本低，一根鋸條使用壽命等同于50-80片砂輪切割片，較電能鋸節能60%
萬澤錦達銷售經理金志鵬電話13934240041
長處：安全防爆、輕盈便攜、鋸割規模廣泛。
手持式氣動切開鋸慣例技術參數：
|
型號 |
功率 |
耗氣量(m3/min) |
切開厚度 |
切開寬度（直徑） |
鋸片速度 |
分量 |
|
120 |
0.5kw |
0.6 |
三種鋸片： |
120mm |
60m/min |
6kg |
|
180 |
1.0kw |
1.2 |
180mm |
90m/min |
10kg |
|
|
230 |
1.5kw |
1.5 |
230mm |
120m/min |
16kg |
FDJ-120型礦用管道切開鋸、電纜無火花切開鋸、FDJ-120型煤礦井下角鋼切開鋸、礦用防爆構造鋼切開鋸、FDJ-120型巷道U型鋼切開鋸、工字鋼無火花切開機、FDJ-120型軌跡堵截切開鋸、煤礦井下鏈條截斷切開鋸、FDJ-120型礦用錨桿切開鋸、錨索氣動無火花手持
陜西寶雞FDJ-120防爆切割鋸供應商
萬澤錦達銷售經理金志鵬電話13934240041
FDJ-120/180/230型手持式風切開鋸運用方法：
1、了解所需切開的資料，如有必要能夠經過下降空氣壓力來下降鋸片的滾動速度。
2、保證牢固固定了所需切開的資料，防止其移動。
3、氣動空氣馬達時，用手指按壓閥桿，然后開端切開。
4、用鋸的分量來控制切開壓力。關于較軟的資料來說，這么的分量現已滿足。過多的壓力會下降鋸片的速度。關于較硬的資料，能夠經過加壓的方法來下降鋸片的滾動速度。切開是堅持鋸垂直。鋸片的任何歪曲或傾斜都也許下降其運用壽命。
陜西寶雞FDJ-120防爆切割鋸供應商
萬澤錦達銷售經理金志鵬電話13934240041
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be completed, do not make the saw touch your body, the workpiece, or the other people in the vicinity. Pneumatic chain sawing motor power large)
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
Sales of FDJ-120U type steel in Henan, Luoyang
Contact gold manager phone 13934240041
