- 產品
- 供應
- 公司
- 新聞
|
|
||||||||||||||||||||||||||||
商品介紹：
·FDJ-120型風動切開鋸適用于風險的作業環境，可在較高溫的環境下作業，無火花，在濕潤的環境中無漏電風險，是一款功能牢靠、安全型及效率極高的抱負風動東西之一。廣泛用于采礦、石化、修建等職業。
·使用井下壓風管道體系作為動力源。重量輕，易帶著；構造科學，便于作業。 思禮鎮FDJ-120/礦用防爆切割鋸
·可迅速切開管道、電纜、角鋼、構造鋼、U型鋼、鏈條、錨桿、錨索等。
·錮金屬鋼合金超級鋸條，冷切割、耐沖突、運用壽數長。十分適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。
貴州六盤水FDJ-120切割鋸送福利
萬澤錦達銷售經理金志鵬聯系電話13934240041
一、便攜式風動切割鋸使用方法：
1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。
2、確保牢固固定了所需切割的材料，防止其移動。
3、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。
4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）
5、關閉空氣馬達時，釋放閥桿。
6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。
7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。
8、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。
9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
技術參數：
型號
功率
耗氣量
切割厚度
切割寬度（直徑）
鋸片速度
重量
FDJ-120
0.5kw
0.6m3/min
三種鋸片：
0—30mm
30—50mm
50—120mm
120mm
60m/min
6kg
FDJ-180
1.0kw
1.2m3/min
180mm
90m/min
10kg
FDJ-230
1.5kw
1.5m3/min
230mm
120m/min
16kg
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be completed, do not make the saw touch your body, the workpiece, or the other people in the vicinity. Pneumatic chain sawing motor power large)
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
Sales of FDJ-120U type steel in Henan, Luoyang
Contact gold manager phone 13934240041
