產品（FDJ-120型風動切割鋸）介紹： RHJ-120型乳化液切割鋸，適用于較危險的工作環境，可在較高溫的環境下作業，無火花，在潮濕的環境中無漏電危險，是一款性能可靠、安全型及效率極高的理想風動工具之一。廣泛用于采礦、石化、建筑等行業。 利用井下乳化液系統作為動力源。重量輕，易攜帶；結構科學，便于作業。 可快速切割管道、電纜、角鋼、結構鋼、U型鋼、工字鋼、軌道、鏈條、錨桿、錨索等。 錮金屬鋼合金超級鋸條，耐高溫、耐摩擦、使用壽命長。非常適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。 優點：安全防爆、輕巧便攜、鋸割范圍廣泛。 手持式氣動/乳化液切割鋸常規技術參數： 型號 功率 耗氣量(m3/min) 切割厚度 切割寬度（直徑） 鋸片速度 重量 120 0.5kw 0.6 三種鋸片： 0—30mm 30—50mm 50—120mm 120mm 60m/min 6kg 180 1.0kw 1.2 180mm 90m/min 10kg 230 1.5kw 1.5 230mm 120m/min 16kg更多關于礦用風動切割鋸的介紹： 錨桿切割鋸是在煤礦巷道掘進支護、修巷時,用于修整錨桿長度的一種支護工具,它可安全快速地切斷直徑24 mm以下的高強度錨桿；此外,它還解決了進風區、老塘、采空區、回風區、落山角的頂板快速放頂問題,使瓦斯、煤塵積存量縮小,預防了瓦斯、煤塵積存的隱患。 切割材料及適用范圍：（手持式防爆切割鋸主要應用煤礦井下、高瓦斯礦井、石油管道、天然氣管道、電纜等切割，要求切割過程不允許產生火花） 鐵管、鋼筋、電纜、銅管、鐵棒、銅棒、錨桿、錨索、鋼筋網、工字鋼、槽鋼、U型鋼、H鋼、角鋼、礦工鋼、軌道鋼、C型鋼。 FDJ-120型礦用乳化液管道切割鋸、電纜乳化液無火花切割鋸、乳化液-120型煤礦井下角鋼切割鋸、礦用防爆結構鋼切割鋸、FDJ-120型巷道U型鋼切割鋸、工字鋼無火花切割機、FDJ-120型軌道切斷切割鋸、煤礦井下鏈條截斷切割鋸、FDJ-120型礦用錨桿切割鋸、錨索氣動無火花手持式切割鋸… FDJ-120/180/230型手持式乳化液/風切割鋸使用方法： 1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。 2、確保牢固固定了所需切割的材料，防止其移動。 3、乳化液馬達時，用手指按壓閥桿，然后開始切割。 4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。） 5、關閉空氣馬達時，釋放閥桿。 6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。 7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。 8、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。 9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。 山西萬澤錦達機械設備制造有限公司，2002年就開始從事了礦山開采的具體工作，后來根據自己工程需求量，自己開始研發生產系列開采需要的機械，并轉型為今天客戶遍布全國，機械制造行業的領軍企業。是一家專門從事礦山設備的廠家，公司生產的礦用/乳化液風動切割鋸技術成熟，質量過硬。More about mine pneumatic cutting saw: bolt cutting saw is in mine roadway, the roadway repair, used to trim the length of anchor a supporting tool, it can be safely and quickly cut off the high strength bolt diameter below 24 mm; in addition, it also solves the problem of air inlet area, goaf, goaf area, return area, off the roof caving fast problem mountain angle, the accumulation of gas and coal dust emissions reduced, preventing the accumulation of gas and coal dust hazard. The cutting material and the applicable scope: (portable explosion-proof cutting saw is mainly used in underground coal mine, high gas mine, oil pipelines, gas pipelines, cables and other requirements of cutting, cutting process is not allowed to produce sparks) pipe, steel, copper, iron, copper, cable, anchor, steel mesh, I-beam, channel steel, U H steel, steel, steel, steel, steel, coal miners C steel rail. FDJ-120 type mine emulsion pipe cutting saw, cable emulsion non spark cutting saw, the emulsion of -120 type coal mine angle cutting saw, mine explosion-proof structure steel cutting saw, FDJ-120 type tunnel U type steel cutting saw, I-beam without spark cutting machine, FDJ-120 type track cutting cutting saw, chain saw, cutting off the coal mine FDJ-120 type mine anchor cable cutting saw, pneumatic hand-held cutting saw no spark... FDJ-120/180/230 handheld emulsion / wind cutting saw method: 1. Understand the materials needed for cutting. If necessary, reduce the air pressure to reduce the rotation speed of saw blades. 2, ensure that the required cutting material is firmly fixed to prevent its movement. 3. When the emulsion motor is motor, the stem is pressed with the finger and then the cutting is started. 4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity. 5. When the air motor is closed, the stem is released. 6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw. 7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose. 8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane. 9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod. Shanxi million Zejin Machinery Equipment Manufacturing Co., in 2002 began to engage in the specific work of mining engineering, then according to their own demand, starting their own R & D and production of series of mining machinery needs, and transformation into today, customers all over the country, machinery manufacturing industry leader. It is a factory specializing in mining equipment, the company produces the mine / emulsion pneumatic cutting saw technology mature, the quality is excellent.
更多關于礦用風動切割鋸的介紹： 錨桿切割鋸是在煤礦巷道掘進支護、修巷時,用于修整錨桿長度的一種支護工具,它可安全快速地切斷直徑24 mm以下的高強度錨桿；此外,它還解決了進風區、老塘、采空區、回風區、落山角的頂板快速放頂問題,使瓦斯、煤塵積存量縮小,預防了瓦斯、煤塵積存的隱患。 切割材料及適用范圍：（手持式防爆切割鋸主要應用煤礦井下、高瓦斯礦井、石油管道、天然氣管道、電纜等切割，要求切割過程不允許產生火花） 鐵管、鋼筋、電纜、銅管、鐵棒、銅棒、錨桿、錨索、鋼筋網、工字鋼、槽鋼、U型鋼、H鋼、角鋼、礦工鋼、軌道鋼、C型鋼。 FDJ-120型礦用乳化液管道切割鋸、電纜乳化液無火花切割鋸、乳化液-120型煤礦井下角鋼切割鋸、礦用防爆結構鋼切割鋸、FDJ-120型巷道U型鋼切割鋸、工字鋼無火花切割機、FDJ-120型軌道切斷切割鋸、煤礦井下鏈條截斷切割鋸、FDJ-120型礦用錨桿切割鋸、錨索氣動無火花手持式切割鋸… FDJ-120/180/230型手持式乳化液/風切割鋸使用方法： 1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。 2、確保牢固固定了所需切割的材料，防止其移動。 3、乳化液馬達時，用手指按壓閥桿，然后開始切割。 4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。） 5、關閉空氣馬達時，釋放閥桿。 6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。 7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。 8、更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。 9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。 山西萬澤錦達機械設備制造有限公司，2002年就開始從事了礦山開采的具體工作，后來根據自己工程需求量，自己開始研發生產系列開采需要的機械，并轉型為今天客戶遍布全國，機械制造行業的領軍企業。是一家專門從事礦山設備的廠家，公司生產的礦用/乳化液風動切割鋸技術成熟，質量過硬。
More about mine pneumatic cutting saw: bolt cutting saw is in mine roadway, the roadway repair, used to trim the length of anchor a supporting tool, it can be safely and quickly cut off the high strength bolt diameter below 24 mm; in addition, it also solves the problem of air inlet area, goaf, goaf area, return area, off the roof caving fast problem mountain angle, the accumulation of gas and coal dust emissions reduced, preventing the accumulation of gas and coal dust hazard. The cutting material and the applicable scope: (portable explosion-proof cutting saw is mainly used in underground coal mine, high gas mine, oil pipelines, gas pipelines, cables and other requirements of cutting, cutting process is not allowed to produce sparks) pipe, steel, copper, iron, copper, cable, anchor, steel mesh, I-beam, channel steel, U H steel, steel, steel, steel, steel, coal miners C steel rail. FDJ-120 type mine emulsion pipe cutting saw, cable emulsion non spark cutting saw, the emulsion of -120 type coal mine angle cutting saw, mine explosion-proof structure steel cutting saw, FDJ-120 type tunnel U type steel cutting saw, I-beam without spark cutting machine, FDJ-120 type track cutting cutting saw, chain saw, cutting off the coal mine FDJ-120 type mine anchor cable cutting saw, pneumatic hand-held cutting saw no spark... FDJ-120/180/230 handheld emulsion / wind cutting saw method: 1. Understand the materials needed for cutting. If necessary, reduce the air pressure to reduce the rotation speed of saw blades. 2, ensure that the required cutting material is firmly fixed to prevent its movement. 3. When the emulsion motor is motor, the stem is pressed with the finger and then the cutting is started. 4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity. 5. When the air motor is closed, the stem is released. 6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw. 7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose. 8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane. 9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod. Shanxi million Zejin Machinery Equipment Manufacturing Co., in 2002 began to engage in the specific work of mining engineering, then according to their own demand, starting their own R & D and production of series of mining machinery needs, and transformation into today, customers all over the country, machinery manufacturing industry leader. It is a factory specializing in mining equipment, the company produces the mine / emulsion pneumatic cutting saw technology mature, the quality is excellent.
