EMETA MA324 6 1024 AL2 編碼器

EMETA MA324 6 1024 AL2 編碼器Norgren D1025H-A1 氣控閥
" 氣控閥

LFP 48?45,5 45,50 G 2.78 280 G 4050 2600
LFP 48?48 48,20 G 2.94 280 G 4050 2600
PLATA motors cm3/rev G in3/rev bar G psi min?1
LFM 30?22 22,00 G 1.34 280 G 4050 4900
LFM 30?26,5 26,50 G 1.62 280 G 4050 4800
LFM 30?28,5 28,50 G 1.74 280 G 4050 4700
LFM 30?30,2 30,20 G 1.84 280 G 4050 4500
Pumps features
Three?position electrically controlled valve with relief
valve
Electronic control of the rotor start?up and stop ramps
Rotation reverse with controlled delay
Easy integration with the machine cabin controls
Auxiliary gear pump with common suction, available
with either cast?iron or aluminium body
Motors features
Reversible rotation with integral antishock valves
European and SAE standard mounting flanges
Side or rear inlet options
Compact size
DOC 03 R A 19
Variable displacement axial piston pumps
PLATA LVP series
Variable displacement axial piston pumps swash plate design. PLATA pumps are ideally suited for medium and high
pressure open circuit applications.
Displacements from 28,70 cm3/rev G 1.75 in3/rev to 87,90 cm3/rev G 5.36 in3/rev.
Max. peak pressure up to 350 bar G 5100 psi.
Max. speed up to 3000 min?1.
Main characteristics
Max
displacement
Max. continuous
 pressure
Max. speed
PLATA LVP cm3/rev G in3/rev bar G psi min?1
LVP 30 28,70 G 1.75 280 G 4050 3000
LVP 48 45,40 G 2.77 280 G 4050 2600
LVP 75 73,60 G 4.49 280 G 4050 2600
LVP 90 87,90 G 5.36 250 G 3600 2200
Features
Energy savings
Low noise emission
Short response time
Drive shaft bearing suitable for radial and axial loads
Multiple combinations
Controls
Pressure compensator
Flow and pressure compensator (Load?Sensing)
Torque limiter
Electrohydraulic servocontrols
20 DOC 03 R A
Variable displacement axial piston pumps
MVP and MVPD series
Variable displacement axial piston pumps swash plate design ideally suited for open circuit in mobile hydraulic applications.
The compact design allows to be mounted directly on engine motors.
The new “MVPD” series allow higher flow rates than traditional pumps with same dimensions, higher machine speeds
without affecting the design of the hydraulic system and a high power-to-dimensions ratio.
Displacements from 14 cm3/rev G 0.85 in3/rev to 84,7 cm3/rev G 5.17 in3/rev.
Max. peak pressure up to 350 bar G 5100 psi.
Max. speed up to 3700 min?1.
Main characteristics
Max
displacement
Max. continuous
 pressure
Max. speed
MVP cm3/rev G in3/rev bar G psi min?1
MVP 30.28 28,00 G 1.74 280 G 4050 3500
MVP 30.34 34,80 G 2.12 250 G 3600 2900
MVP 48.45 45,00 G 2.75 280 G 4050 3000
 pressure