LAFERT TYPE AMHE 90L CA2 IEC60034

LAFERT TYPE AMHE 90L CA2 IEC60034 電機(jī)

T1A 132M1-6 4 940 5.01 9.59 6.2 81.4 0.74 40.64 2.4 1.9 2.6
T1A 132M2-6 5.5 940 6.34 12.57 6.8 83.1 0.76 55.87 2.3 2 2.6
T1C 160M-6 7.5 950 8.49 16.82 7 84.7 0.76 75.39 2.3 2 2.7
T1C 160L-6 11 955 11.43 23.56 7.3 86.4 0.78 109.99 2.3 2 2.7
T1C 180L-6 15 955 14.84 31.25 7.2 87.7 0.79 149.99 2.3 2 2.7
T1C 200L1-6 18.5 960 15.58 36.31 6.9 88.6 0.83 184.02 2.3 2 2.7
T1C 200L2-6 22 960 18.41 42.89 7.3 89.2 0.83 218.84 2.3 2 2.6
T1C 225M-6 30 970 24.82 57.84 7.4 90.2 0.83 295.34 2.3 2 2.6
T1C 250M-6 37 970 27.94 69.20 7.5 90.8 0.85 364.25 2.3 2 2.7
T1C 280S-6 45 975 32.26 82.63 7.7 91.4 0.86 440.74 2.3 2 2.7
T1C 280M1-6 55 975 37.40 99.29 7.7 91.9 0.87 538.68 2.2 1.9 2.5
T1C 315S-6 75 975 45.71 131.36 7.9 92.6 0.89 734.56 2.1 1.9 2.5
T1C 315M-6 90 975 51.74 155.37 8 92.9 0.90 881.47 2 1.8 2.3
T1C 315L1-6 110 975 62.97 189.09 7.7 93.3 0.90 1077.36 2 1.8 2.3
T1C 315L2-6 132 975 79.68 228.96 .8 93.5 0.89 1292.83 2 1.8 2.3
T1C 355M1-6 160 975 85.93 270.56 7.6 93.8 0.91 1567.06 2 1.8 2.3
T1C 355M2-6 200 975 113.63 341.23 7.8 94 0.90 1958.83 2 1.8 2.3
T1C 355L-6 250 975 150.10 431.33 7.8 94 0.89 2448.54 2 1.8 2.3
6
Model Power
(KW)
Full Load Speed
(r/min)
Inl 400V
(A)
Ifl 400V
(A)
Ist /In
(Times)
Eff.
100%FL
(%)
Power Factor
(CosΦ)
Full Load Torque
(N.M)
Tst /Tn
(Times)
Tmin/Tn
(Times)
Tmax /Tn
(Times)
2 Pole - 3000 rpm Synchronous Speed 50Hz
T2A 801-2 0.75 2848 0.96 1.86 6 77.4 0.75 2.51 2.7 2.1 2.8
T2A 802-2 1.1 2846 1.20 2.52 6.7 79.6 0.79 3.69 2.7 2.1 2.9
T2A 90S-2 1.5 2852 1.32 3.17 6.1 81.3 0.84 5.02 2.3 2 2.7
T2A 90L-2 2.2 2845 1.89 4.54 7 83.2 0.84 7.38 2.6 2.1 2.7
T2A 100L-2 3 2851 2.00 5.75 7.6 84.6 0.89 10.05 2.5 2 2.8
T2A 112M-2 4 2910 2.63 7.56 7.8 85.8 0.89 13.13 2.5 2 2.7
T2A 132S1-2 5.5 2905 3.57 10.25 7.8 87 0.89 18.08 2.4 2 2.9
T2A 132S2-2 7.5 2910 5.06 13.96 7.9 88.1 0.88 24.61 2.7 2 2.8
T2C 160M1-2 11 2920 6.57 19.73 7.9 89.4 0.90 35.97 2.2 2.1 3
T2C 160M2-2 15 2918 8.37 26.35 7.9 90.3 0.91 49.09 2.3 2.1 3
T2C 160L-2 18.5 2922 9.64 31.93 8 90.9 0.92 60.46 2.4 2.1 2.9
T2C 180M-2 22 2930 13.60 39.08 7.5 91.3 0.89 71.70 2.3 2 2.8
T2C 200L1-2 30 2925 19.39 53.49 6.7 92 0.88 97.94 2.4 2 2.7
T2C 200L2-2 37 2930 21.36 64.15 6.3 92.5 0.90 120.59 2.3 2 2.7
T2C 225M-2 45 2930 28.81 79.45 6.9 92.9 0.88 146.66 2.3 2 2.8
T2C 250M-2 55 2940 35.09 96.80 8 93.2 0.88 178.64 2.3 1.9 2.7
T2C 280S-2 75 2940 37.86 125.45 8 93.8 0.92 243.60 2.2 1.9 2.7
T2C 280M-2 90 2940 45.28 150.06 7.7 94.1 0.92 292.33 2.2 1.9 2.6
T2C 315S-2 110 2940 62.30 187.08 7.7 94.3 0.90 357.29 2 1.8 2.3
T2C 315M-2 132 2940 70.29 221.33 7.6 94.6 0.91 428.74 2 1.8 2.3
T2C 315L1-2 160 2945 90.14 270.68 7.8 94.8 0.90 518.81 2 1.8 2.3
T2C 315L2-2 200 2945 118.82 341.44 7.9 95 0.89 648.51 2 1.8 2.3
T2C 355M-2 250 2945 140.54 422.05 7.8 95 0.90 810.64 2 1.8 2.3
T2C 355L-2 315 2945 187.14 537.76 7.8 95 0.89 1021.40 2 1.8 2.3
4 Pole - 1500 rpm Synchronous Speed 50Hz
T2A 802-4 0.75 1420 0.90 1.79 5.4 79.6 0.76 5.04 2.3 2.1 2.9
T2A 90S-4 1.1 1425 1.21 2.50 5.9 81.4 0.78 7.37 2.3 2.1 2.7
T2A 90L-4 1.5 1420 1.57 3.31 6.4 82.8 0.79 10.09 2.4 2 2.7
T2A 100L1-4 2.2 1430 2.03 4.59 6.6 84.3 0.82 14.69 2.4 2.1 2.9
T2A 100L2-4 3 1430 2.94 6.33 6.9 85.5 0.80 20.03 2.4 2 2.8
T2A 112M-4 4 1435 4.01 8.44 7.9 86.6 0.79 26.62 2.5 2 3
T2A 132S-4 5.5 1430 4.87 11.04 7.1 87.7 0.82 36.73 2.3 2 2.8
T2A 132M-4 7.5 1430 6.31 14.70 7.8 88.7 0.83 50.08 2.3 2 2.7
T2C 160M-4 11 1440 6.17 19.43 7.9 89.8 0.91 72.95 2.5 2.1 2.8
T2C 160L-4 15 1445 7.82 25.92 7.8 90.8 0.92 99.13 2.4 2.1 2.9
T2C 180M-4 18.5 1445 12.68 33.66 7.8 91.2 0.87 122.26 2.4 2.1 3
T2C 180L-4 22 1460 13.55 38.95 7.5 91.6 0.89 143.89 2.3 2 3
IE2 Effi ciency Motors Technical Data
7
IE2 Effi ciency Motors Technical Data
Model Power
(KW)
Full Load Speed
(r/min)
Inl 400V
(A)
Ifl 400V
(A)
Ist /In
(Times)
Eff.
100%FL
(%)
Power Factor
(CosΦ)
Full Load Torque
(N.M)
Tst /Tn
(Times)
Tmin/Tn
(Times)
Tmax /Tn
(Times)
T2C 200L-4 30 1460 19.33 53.31 7.9 92.3 0.88 196.22 2.4 2 2.7
T2C 225S-4 37 1470 33.42 72.02 6.7 92.7 0.80 240.36 2.4 2 2.7
T2C 225M-4 45 1480 40.47 87.21 7 93.1 0.80 290.35 2.3 2 2.8
T2C 250M-4 55 1480 34.98 96.49 7.4 93.5 0.88 354.87 2.4 1.9 2.7
T2C 280S-4 75 1480 40.19 126.56 7.5 94 0.91 483.92 2.2 1.9 2.6
T2C 280M-4 90 1480 45.23 149.90 7.7 94.2 0.92 580.70 2.2 1.9 2.6
T2C 315S-4 110 1480 62.17 186.69 7.8 94.5 0.90 709.75 2 1.8 2.3
T2C 315M-4 132 1480 70.22 221.09 7.8 94.7 0.91 851.69 2 1.8 2.3
T2C 315L1-4 160 1480 84.93 267.43 7.9 94.9 0.91 1032.36 2 1.8 2.3
T2C 315L2-4 200 1480 112.32 337.29 7.7 95.1 0.90 1290.45 2 1.8 2.3
T2C 355M-4 250 1480 148.36 426.35 7.9 95.1 0.89 1613.06 2 1.8 2.3
T2C 355L-4 315 1480 176.90 531.23 7.8 95.1 0.90 2032.45 2 1.8 2.3
6 Pole - 1000 rpm Synchronous Speed 50Hz
T2A 90S-6 0.75 935 0.95 1.88 6.2 75.9 0.76 7.66 2.2 2 2.7
T2A 90L-6 1.1 935 1.18 2.54 6 78.1 0.80 11.23 2.3 2.1 2.6
T2A 100L-6 1.5 940 1.46 3.31 5.8 79.8 0.82 15.24 2.3 2.1 2.7
T2A 112M-6 2.2 940 2.25 4.85 6.4 81.8 0.80 22.35 2.3 2.1 2.9
T2A 132S-6 3 940 2.69 6.26 6.3 83.3 0.83 30.48 2.4 2.2 2.8
T2A 132M1-6 4 945 3.39 8.12 6.2 84.6 0.84 40.42 2.5 2 2.8
T2A 132M2-6 5.5 945 4.97 11.26 6.8 86 0.82 55.58 2.3 1.9 2.8
T2C 160M-6 7.5 955 6.16 14.78 7 87.2 0.84 74.99 2.4 1.9 2.7
T2C 160L-6 11 960 8.50 21.06 7.3 88.7 0.85 109.42 2.5 2 2.8
T2C 180L-6 15 960 12.48 29.08 7.8 89.7 0.83 149.21 2.3 2.1 2.9
T2C 200L1-6 18.5 965 14.03 34.75 7.8 90.4 0.85 183.07 2.4 2.1 3.2
T2C 200L2-6 22 965 15.86 40.62 7.9 90.9 0.86 217.70 2.3 1.9 3.1
T2C 225M-6 30 975 22.43 55.56 7.9 91.7 0.85 293.82 2.2 1.9 2.7
T2C 250M-6 37 975 29.95 69.79 7.5 92.2 0.83 362.38 2.3 2.1 2.7
T2C 280S-6 45 980 31.81 81.48 7.2 92.7 0.86 438.49 2.3 2 2.8
T2C 280M1-6 55 980 38.71 99.15 7.7 93.1 0.86 535.93 2.2 1.9 2.7
T2C 315S-6 75 980 45.17 129.81 7.9 93.7 0.89 730.81 2.1 1.9 2.5
T2C 315M-6 90 980 51.13 153.56 8 94 0.90 876.98 2 1.8 2.3
T2C 315L1-6 110 980 62.30 187.08 7.7 94.3 0.90 1071.86 2 1.8 2.3
T2C 315L2-6 132 980 78.75 226.30 .8 94.6 0.89 1286.23 2 1.8 2.3
T2C 355M1-6 160 980 85.02 267.71 7.6 94.8 0.91 1559.07 2 1.8 2.3
T2C 355M2-6 200 980 112.43 337.64 7.8 95 0.90 1948.84 2 1.8 2.3
T2C 355L-6 250 980 148.52 426.79 7.8 95 0.89 2436.05 2 1.8 2.3
8
Model Power
(KW)
Full Load Speed
(r/min)
Inl 400V
(A)
Ifl 400V
(A)
Ist /In
(Times)
Eff.
100%FL
(%)
Power Factor
(CosΦ)
Full Load Torque
(N.M)
Tst /Tn
(Times)
Tmin/Tn
(Times)
Tmax /Tn
(Times)
2 Pole - 3000 rpm Synchronous Speed 50Hz
T3A 801-2 0.75 2848 0.92 1.79 6 80.7 0.75 2.51 2.7 2.1 2.8
T3A 802-2 1.1 2846 1.15 2.43 6.7 82.7 0.79 3.69 2.7 2.1 2.9
T3A 90S-2 1.5 2852 1.28 3.06 6.1 84.2 0.84 5.02 2.3 2 2.7
T3A 90L-2 2.2 2845 1.83 4.40 7 85.9 0.84 7.38 2.6 2.1 2.7
T3A 100L-2 3 2851 1.94 5.59 7.6 87.1 0.89 10.05 2.5 2 2.8
T3A 112M-2 4 2910 2.56 7.36 7.8 88.1 0.89 13.13 2.5 2 2.7
T3A 132S1-2 5.5 2905 3.48 10.00 7.8 89.2 0.89 18.08 2.4 2 2.9
T3A 132S2-2 7.5 2910 4.95 13.65 7.9 90.1 0.88 24.61 2.7 2 2.8
T3C 160M1-2 11 2920 6.44 19.34 7.9 91.2 0.90 35.97 2.2 2.1 3
T3C 160M2-2 15 2918 8.22 25.89 7.9 91.9 0.91 49.09 2.3 2.1 3
T3C 160L-2 18.5 2922 9.48 31.41 8 92.4 0.92 60.46 2.4 2.1 2.9
T3C 180M-2 22 2930 13.39 38.49 7.5 92.7 0.89 71.70 2.3 2 2.8
T3C 200L1-2 30 2925 19.12 52.74 6.7 93.3 0.88 97.94 2.4 2 2.7
T3C 200L2-2 37 2930 21.09 63.33 6.3 93.7 0.90 120.59 2.3 2 2.7
T3C 225M-2 45 2930 28.47 78.52 6.9 94 0.88 146.66 2.3 2 2.8
T3C 250M-2 55 2940 34.68 95.67 8 94.3 0.88 178.64 2.3 1.9 2.7
T3C 280S-2 75 2940 37.50 124.26 8 94.7 0.92 243.60 2.2 1.9 2.7
T3C 280M-2 90 2940 44.85 148.64 7.7 95 0.92 292.33 2.2 1.9 2.6
T3C 315S-2 110 2940 61.71 185.31 7.7 95.2 0.90 357.29 2 1.8 2.3
T3C 315M-2 132 2940 69.70 219.47 7.6 95.4 0.91 428.74 2 1.8 2.3
T3C 315L1-2 160 2945 89.20 267.86 7.8 95.8 0.90 518.81 2 1.8 2.3
T3C 315L2-2 200 2945 117.82 338.58 7.9 95.8 0.89 648.51 2 1.8 2.3
T3C 355M-2 250 2945 139.37 418.53 7.8 95.8 0.90 810.64 2 1.8 2.3
T3C 355L-2 315 2945 185.57 533.27 7.8 95.8 0.89 1021.40 2 1.8 2.3
4 Pole - 1500 rpm Synchronous Speed 50Hz
T3A 802-4 0.75 1420 0.87 1.73 5.4 82.5 0.76 5.04 2.3 2.1 2.9
T3A 90S-4 1.1 1425 1.17 2.42 5.9 84.1 0.78 7.37 2.3 2.1 2.7
T3A 90L-4 1.5 1420 1.53 3.21 6.4 85.3 0.79 10.09 2.4 2 2.7
T3A 100L1-4 2.2 1430 1.97 4.47 6.6 86.7 0.82 14.69 2.4 2.1 2.9
T3A 100L2-4 3 1430 2.86 6.17 6.9 87.7 0.80 20.03 2.4 2 2.8
T3A 112M-4 4 1435 3.92 8.25 7.9 88.6 0.79 26.62 2.5 2 3
T3A 132S-4 5.5 1430 4.77 10.81 7.1 89.6 0.82 36.73 2.3 2 2.8
T3A 132M-4 7.5 1430 6.19 14.43 7.8 90.4 0.83 50.08 2.3 2 2.7
T3C 160M-4 11 1440 6.06 19.09 7.9 91.4 0.91 72.95 2.5 2.1 2.8
T3C 160L-4 15 1445 7.71 25.55 7.8 92.1 0.92 99.13 2.4 2.1 2.9
T3C 180M-4 18.5 1445 12.49 33.15 7.8 92.6 0.87 122.26 2.4 2.1 3
T3C 180L-4 22 1460 13.35 38.37 7.5 93 0.89 143.89 2.3 2 3
T3C 200L-4 30 1460 19.06 52.57 7.9 93.6 0.88 196.22 2.4 2 2.7
T3C 225S-4 37 1470 32.99 71.09 6.7 93.9 0.80 240.36 2.4 2 2.7
T3C 225M-4 45 1480 39.99 86.19 7 94.2 0.80 290.35 2.3 2 2.8
T3C 250M-4 55 1480 34.57 95.36 7.4 94.6 0.88 354.87 2.4 1.9 2.7
T3C 280S-4 75 1480 39.77 125.22 7.5 95 0.91 483.92 2.2 1.9 2.6
T3C 280M-4 90 1480 44.76 148.32 7.7 95.2 0.92 580.70 2.2 1.9 2.6
T3C 315S-4 110 1480 61.58 184.92 7.8 95.4 0.90 709.75 2 1.8 2.3
T3C 315M-4 132 1480 69.56 219.01 7.8 95.6 0.91 851.69 2 1.8 2.3
T3C 315L1-4 160 1480 84.13 264.91 7.9 95.8 0.91 1032.36 2 1.8 2.3
T3C 315L2-4 200 1480 111.26 334.12 7.7 96 0.90 1290.45 2 1.8 2.3
T3C 355M-4 250 1480 146.97 422.35 7.9 96 0.89 1613.06 2 1.8 2.3
T3C 355L-4 315 1480 175.24 526.25 7.8 96 0.90 2032.45 2 1.8 2.3
6 Pole - 1000 rpm Synchronous Speed 50Hz
T3A 90S-6 0.75 935 0.91 1.81 6.2 78.9 0.76 7.66 2.2 2 2.7
T3A 90L-6 1.1 935 1.14 2.45 6 81 0.80 11.23 2.3 2.1 2.6
T3A 100L-6 1.5 940 1.41 3.20 5.8 82.5 0.82 15.24 2.3 2.1 2.7
T3A 112M-6 2.2 940 2.18 4.71 6.4 84.3 0.80 22.35 2.3 2.1 2.9
T3A 132S-6 3 940 2.62 6.09 6.3 85.6 0.83 30.48 2.4 2.2 2.8
T3A 132M1-6 4 945 3.30 7.92 6.2 86.8 0.84 40.42 2.5 2 2.8
T3A 132M2-6 5.5 945 4.85 11.00 6.8 88 0.82 55.58 2.3 1.9 2.8
T3C 160M-6 7.5 955 6.03 14.46 7 89.1 0.84 74.99 2.4 1.9 2.7
T3C 160L-6 11 960 8.35 20.69 7.3 90.3 0.85 109.42 2.5 2 2.8
T3C 180L-6 15 960 12.27 28.60 7.8 91.2 0.83 149.21 2.3 2.1 2.9
T3C 200L1-6 18.5 965 13.83 34.26 7.8 91.7 0.85 183.07 2.4 2.1 3.2
T3C 200L2-6 22 965 15.64 40.05 7.9 92.2 0.86 217.70 2.3 1.9 3.1
T3C 225M-6 30 975 22.14 54.84 7.9 92.9 0.85 293.82 2.2 1.9 2.7
T3C 250M-6 37 975 29.59 68.97 7.5 93.3 0.83 362.38 2.3 2.1 2.7
T3C 280S-6 45 980 31.47 80.61 7.2 93.7 0.86 438.49 2.3 2 2.8
T3C 280M1-6 55 980 38.30 98.10 7.7 94.1 0.86 535.93 2.2 1.9 2.7
T3C 315S-6 75 980 44.74 128.58 7.9 94.6 0.89 730.81 2.1 1.9 2.5
T3C 315M-6 90 980 50.65 152.10 8 94.9 0.90 876.98 2 1.8 2.3
T3C 315L1-6 110 980 61.77 185.51 7.7 95.1 0.90 1071.86 2 1.8 2.3
T3C 315L2-6 132 980 78.09 224.40 .8 95.4 0.89 1286.23 2 1.8 2.3
T3C 355M1-6 160 980 84.31 265.47 7.6 95.6 0.91 1559.07 2 1.8 2.3
T3C 355M2-6 200 980 111.50 334.82 7.8 95.8 0.90 1948.84 2 1.8 2.3
T3C 355L-6 250 980 147.28 423.23 7.8 95.8 0.89 2436.05 2 1.8 2.3
IE3 Effi ciency Motors Technical Data
Various Certificates
E323353
R
C US

Entek 2100 Series Family
of Non Contact Pickups
A variety of systems
to meet your specific needs
A variety of systems
to meet your specific needs
Measurement systems for:
? Radial Vibration ? Eccentricity
? Axial Vibration ? Case Expansion
? Speed Reference? Differential Expansion
? Phase Reference ? Thrust
The 2100 Series from Rockwell Automation
Entek is a family of sensors designed to
meet the stringent requirements of
the American Petroleum Institute
(API) Standard 670.
The sensors are non-contacting
eddy-current type transducers that
measure the dynamic and/or static
displacement of the target relative to
the mounting fixture. These systems are
typically used to measure the vibration of rotating
machinery such as turbines, compressors, large pumps and other,
usually critical, machines.
Why Choose Entek Probe Systems?
Entek has been designing and supplying probes for over 20 years. This
vast experience has culminated in the 2100 Series - one of the most
advanced Non-Contact Probe Sensing System available today. The 2100
Series has introduced new standards in terms of accuracy, reliability and
ease of machinery monitoring system integration.
The Entek non-contact probe systems are widely used to measure
vibration in high-speed machines with relatively lightweight rotors and
rigid bearings (turbines, centrifugal pumps and compressors). The probe
system, consisting of a non-contact pickup probe, oscillator/demodulator
(probe driver) and interconnecting cable, can be used to measure shaft
radial and axial vibration, shaft eccentricity, shaft axial position, case
expansion, differential expansion and other instances where noncontacting,
relative measurements must be made. The Entek probe/driver
systems are designed to meet the requirements of API 670 assisting you
with the applicability, capability and reliability that you require in your
machinery monitoring and protection systems.
Non-Contact Pick-Up Probe
Entek’s non-contact pick-up probes are an encapsulated wire
configuration that reads the relative position of the equipment by
introducing eddy currents into the target material and measuring the
change in the current as the target surface moves. The energy loss into
the target increases / decreases as the target moves nearer to or further
away from the probe. The change in energy loss is detected as a change
in the modulated signal, which produces a voltage proportional to the
gap between the probe tip and the target. This signal is fed to the
monitoring system providing a continuous, and very accurate measure of
the relative distance to the target surface.
Extension Cable
The extension cable provides flexibility for placement of the probe by
allowing extended lengths between the driver and the non-contact pickup.
A variety of Teflon-insulated and Armour coaxial extension cables
adapt the sensor system to most installations. To insure the accuracy of
the measurement, the extension cables are ‘electrically matched’ to the
selected probe system.
Probe Driver
Entek’s stainless steel probe drivers provide the ‘radio frequency’ which
powers the probe system. The driver is the primary component
responsible for signal conditioning, providing accurate linearity over the
operating range of the system. Entek’s probe driver systems are case
grounded and therefore must be isolated during installation.
The 2100 Series of probes are available in two designs, standard
and advanced depending on your application requirements.
Entek’s Standard 2100 Series Probes
Offered in 5mm, 8mm and a variety of long-range designs, these probes
satisfy the requirements of API 670 with respect to scale factor error,
interchangeability, and sensor size. These sensors are well suited for
most typical shaft vibration monitoring applications.
Entek’s Advanced Design 2190 Series Probes
Offered in 8mm sizes only, these probes satisfy the requirements of API
670 in all respects. These probes, which offer the necessary low
temperature drift and stability necessary for bearing position
measurements, are well suited for the bearing position and differential
expansion measurements required by many Turbine Supervisory
Instrumentation (TSI) systems.
Intrinsic Safety Explosion Proof Rating
CSA International: Class I, Division 2, Groups A, B, C and D.
CSA Certificate No.: 216284
Date Issued: June 4, 2002
Factory Mutual (FM): Class I, II, and III, Division 1,
Groups A, B, C D, E, F and G.
Application for 2100 series is pending.
ATEX: Application for 2100 series is pending
Probe System Selection
A probe system is composed of three elements including the probe, the
extension cable, and the oscillator/demodulator, usually referred to as
simply the driver. Selections for each of these are included in the
following tables. To select a probe system, first choose the probe that is
right for your application. Then select a compatible extension cable, of
the desired length, and a suitable driver.
First determine if your applications requirements can be met with the
Standard 2100 Series probes, usually it can, or if it will require the
Advanced Design 2190 Series probes. Next, consider the probe size
requirements. A probes most important feature, the tip diameter,
normally characterizes the probe. For example, an ‘8mm probe system’
refers to a probe with a tip diameter of 8mm. In general, the wider the tip,
the longer the sensing range of the probe. Of course there are other
characteristics that are important as well such as the body length and the
thread size. Basically, choose the tip size based on the application. Choose
the remaining characteristics based on the specifics of the installation.
UNTHREADED
WITH CONNECTOR=1
WITHOUT CONNECTOR=0
BODY
MODEL 21AA B C D E
Figure 1
OVERALL LENGTH
COMPLIANT
210X 2111-2114 2118-
80 mil Transducer 180 mil Transducer Thrust Positio
Linear Range* Apx. 80 mils (2,000 μm) Apx. 180 mils (4,500 μm) Apx. 236 m
Sensitivity* 200m V/mil (787mV/100μm) 100m V/mil (394mV/100μm) 63.5m V/mi
Sensitivity Error*
Scale Factor Error* Within ±5% of 200mV/mil Within ±10% of 100mV/mil
(if calibrated as a system) (if calibrated as a system)
Linearity* Within ±0.8 mils of 200mV/mil Within ±2.9 mils of 100mV/mil Within ±
(if calibrated as a system) (if calibrated as a system) (if calibrated
Within ±
(When interchangeabil
Operating Sensor -40 to +350°F (-40 to +177°C)
Temperature Extension cable Connector: max. 257°F (+125°C)
Range Driver -36 to +176°F (-38 to +80°C)
Operating Humidity Range 30 to 95% RH (noncondensing, non-submerged)
Power Supply -17.5VDC to -26VDC
Max. Output Voltage Apx. -22VDC (at - 24VDC power supply voltage)
Current Consumption Max: -16mA Max: -20mA Max: -
(at 10k ? load resistance)
Frequency response DC to 20kHz (-3dB) DC to 10kHz (-3dB) DC to 10k
Output Impedance 50?
Sensor Tip Diameter Apx. 5mm or Apx. 8mm Apx. 11mm Apx. 1
Cable Tip Diameter
Connector Tip Diameter
Connector Material Stainless steel, gold plated finish
Sensor Cable Length 0.5m or 1m
System Cable Length Sensor cable length + Extension cable length=
5m ±10% or 9m ±10%
* At -24VDC power supply, 77°F (25°C) and calibrated to a flat surface of AISI 4140 steel (thickness 200mils or 5mm).
-2119 2125-2128 2150-2151 219X
on Transducer Diff. Expansion Transducer Diff Expansion Transducer Vibration transducer
mils (6mm) Apx. 531 mils (13.5mm) Apx. 1022 mils (26mm) >79 mils (2mm) (begins at Apx.
12 mils (0.3mm) from sensor tip)
l (2.5V/mm) 20.3m V/mil (0.8V/mm) 10.15m V/mil (0.4V/mm) 200mV/mil (787mV/100μm)
Within ±4% Within ±4%
Within ±4% of 200mV/mil
(if calibrated as a system)
Within ±10% of 200mV/mil
(including interchangeability
errors)
±3.5 mils Within ±7.8 mils Within ±9.8mils (±250μm) Within ±1mil (±25μm)
as a system) (if calibrated as a system) (if calibrated as a system) (if calibrated as a system)
±4.7 mils Within ±10.6 mils Within ±15.7mils (±400μm) Within ±1.8mils (±45μm)
ity errors are included) (When interchangeability errors are included) (when interchangeability errors are included) (when interchangeability errors are included)
-40 to +257°F (-40 to +125°C) -40 to +257°F (-40 to +125°C)
Connector: max. 257°F (+125°C) Connector: max. 257°F (+125°C)
-36 to +176°F (-38 to +80°C) -36 to +176°F (-38 to +80°C)
30 to 95% RH (noncondensing, non-submerged) 30 to 95% RH (noncondensing, non-submerged)
(sensor body: 100%)
-24VDC ±10% -24VDC ±10%
Apx. -22VDC (at - 24VDC power supply voltage) Apx. -22VDC (at - 24VDC power supply voltage)
-13mA Max: -15mA Max: -13mA Max: -16mA
kHz (-3dB) DC to 3kHz (-3dB) DC to 3kHz (-3dB) DC to 10kHz (-3dB)
50? 50?
18mm Apx. 25mm Apx. 50mm Apx. 8mm
Max. Apx. 6mm Max. Apx. 6mm
Max. Apx. 9.5mm (gold plated SMA connector) Max. Apx. 9.5mm (gold plated SMA connector)
Stainless steel, gold plated finish Stainless steel, gold plated finish
Sensor cable length + Extension cable length= Sensor cable length + Extension cable length=
5m ±10% or 9m ±10% 5m ±10% or 9m ±10%
Probe Configurations (Refer to Figure 1 for identification)
2100 Series Standard 5mm Probes
Probe Range Sensitivity Body Length Non-Thread Probe/Cable Thread Size Armour Rev. Right
Part Number Tip Dia. (mV/mil) “B“ Dim Length “C“ Length”E” Cable Mount Angle
Dim Dim
2101/30/03/1/10 5mm 80mils 200 30mm 3mm 1.0 meter 1/4-28 No No No
2101/50/03/1/10 5mm 80mils 200 50mm 3mm 1.0 meter 1/4-28 No No No
2101/70/03/1/10 5mm 80mils 200 70mm 3mm 1.0 meter 1/4-28 No No No
2101/90/03/1/10 5mm 80mils 200 90mm 3mm 1.0 meter 1/4-28 No No No
2101/120/03/1/1 5mm 80mils 200 120mm 3mm 1.0 meter 1/4-28 No No No
2101/150/03/1/1 5mm 80mils 200 150mm 3mm 1.0 meter 1/4-28 No No No
2102/30/03/1/10 5mm 80mils 200 30mm 3mm 1.0 meter 1/4-28 Yes No No
2102/50/03/1/10 5mm 80mils 200 50mm 3mm 1.0 meter 1/4-28 Yes No No
2102/70/03/1/10 5mm 80mils 200 70mm 3mm 1.0 meter 1/4-28 Yes No No
2102/90/03/1/10 5mm 80mils 200 90mm 3mm 1.0 meter 1/4-28 Yes No No
2102/120/03/1/1 5mm 80mils 200 120mm 3mm 1.0 meter 1/4-28 Yes No No
2102/150/03/1/1 5mm 80mils 200 150mm 3mm 1.0 meter 1/4-28 Yes No No
2103/30/03/1/10 5mm 80mils 200 30mm 3mm 1.0 meter M8x1 No No No
2103/50/03/1/10 5mm 80mils 200 50mm 3mm 1.0 meter M8x1 No No No
2103/70/03/1/10 5mm 80mils 200 70mm 3mm 1.0 meter M8x1 No No No
2103/90/03/1/10 5mm 80mils 200 90mm 3mm 1.0 meter M8x1 No No No
2103/120/03/1/10 5mm 80mils 200 120mm 3mm 1.0 meter M8x1 No No No
2103/150/03/1/10 5mm 80mils 200 150mm 3mm 1.0 meter M8x1 No No No
2104/30/03/1/10 5mm 80mils 200 30mm 3mm 1.0 meter M8x1 Yes No No
2104/50/03/1/10 5mm 80mils 200 50mm 3mm 1.0 meter M8x1 Yes No No
2104/70/03/1/10 5mm 80mils 200 70mm 3mm 1.0 meter M8x1 Yes No No
2104/90/03/1/10 5mm 80mils 200 90mm 3mm 1.0 meter M8x1 Yes No No
2104/120/03/1/10 5mm 80mils 200 120mm 3mm 1.0 meter M8x1 Yes No No
2104/150/03/1/10 5mm 80mils 200 150mm 3mm 1.0 meter M8x1 Yes No No
2100 Series Standard 8mm Probes
Probe Range Sensitivity Body Length Non-Thread Probe/Cable Thread Size Armour Rev. Right
Part Number Tip Dia. (mV/mil) “B“ Dim Length “C“ Length”E” Cable Mount Angle
Dim Dim
2105/30/00/1/10 8mm 80mils 200 30mm 0 1.0 meter 3/8-24 No No No
2105/50/00/1/10 8mm 80mils 200 50mm 0 1.0 meter 3/8-24 No No No
2105/70/00/1/10 8mm 80mils 200 70mm 0 1.0 meter 3/8-24 No No No
2105/90/00/1/10 8mm 80mils 200 90mm 0 1.0 meter 3/8-24 No No No
2105/120/00/1/10 8mm 80mils 200 120mm 0 1.0 meter 3/8-24 No No No
2105/150/00/1/10 8mm 80mils 200 150mm 0 1.0 meter 3/8-24 No No No
2106/30/00/1/10 8mm 80mils 200 30mm 0 1.0 meter 3/8-24 Yes No No
2106/50/00/1/10 8mm 80mils 200 50mm 0 1.0 meter 3/8-24 Yes No No
2106/70/00/1/10 8mm 80mils 200 70mm 0 1.0 meter 3/8-24 Yes No No
2106/90/00/1/10 8mm 80mils 200 90mm 0 1.0 meter 3/8-24 Yes No No
2106/120/00/1/10 8mm 80mils 200 120mm 0 1.0 meter 3/8-24 Yes No No
2106/150/00/1/10 8mm 80mils 200 150mm 0 1.0 meter 3/8-24 Yes No No
2107/30/00/1/10 8mm 80mils 200 30mm 0 1.0 meter M10x1 No No No
2107/50/00/1/10 8mm 80mils 200 50mm 0 1.0 meter M10x1 No No No
2107/70/00/1/10 8mm 80mils 200 70mm 0 1.0 meter M10x1 No No No
2107/90/00/1/10 8mm 80mils 200 90mm 0 1.0 meter M10x1 No No No
2107/120/00/1/10 8mm 80mils 200 120mm 0 1.0 meter M10x1 No No No
2107/150/00/1/10 8mm 80mils 200 150mm 0 1.0 meter M10x1 No No No
2108/30/00/1/10 8mm 80mils 200 30mm 0 1.0 meter M10x1 Yes No No
2108/50/00/1/10 8mm 80mils 200 50mm 0 1.0 meter M10x1 Yes No No
2108/70/00/1/10 8mm 80mils 200 70mm 0 1.0 meter M10x1 Yes No No
2108/90/00/1/10 8mm 80mils 200 90mm 0 1.0 meter M10x1 Yes No No
2108/120/00/1/10 8mm 80mils 200 120mm 0 1.0 meter M10x1 Yes No No
2108/150/00/1/10 8mm 80mils 200 150mm 0 1.0 meter M10x1 Yes No No
2109/30/05/1/05 8mm 80mils 200 30mm 5mm 0.5 meter 3/8-24 No Yes No
2109/30/05/1/10 8mm 80mils 200 30mm 5mm 1.0 meter 3/8-24 No Yes No
2100 Series Standard Probe Extension Cables
Probe Cable Armour
Part Number Tip Dia. Length Cable
2170/0/40 5/8mm 4.0m No
2170/1/40 5/8mm 4.0m Yes
2170/0/45 5/8mm 4.5m No
2170/0/80 5/8mm 8.0m No
2170/1/80 5/8mm 8.0m Yes
2170/0/85 5/8mm 8.5m No
2171/0/40 11mm 4.0m No
2171/1/40 11mm 4.0m Yes
2171/0/80 11mm 8.0m No
2171/1/80 11mm 8.0m Yes
2172/1/40 18mm 4.0m Yes
2172/1/80 18mm 8.0m Yes
2173/1/40 25.4mm 4.0m Yes
2173/1/80 25.4mm 8.0m Yes
2174/1/40 50mm 4.0m Yes
2174/1/80 50mm 8.0m Yes
2100 Series Standard Long Range Probes
Probe Range Sensitivity Body Length Non-Thread Probe/Cable Thread Size Armour Rev. Right
Part Number Tip Dia. (mV/mil) “B“ Dim Length “C“ Length”E” Cable Mount Angle
Dim Dim
2111/40/00/1/10 11mm 180mils 100 40mm 5mm 1.0 meter 1/2-20 No No No
2112/40/00/1/10 11mm 180mils 100 40mm 5mm 1.0 meter 1/2-20 Yes No No
2113/40/00/1/10 11mm 180mils 100 40mm 5mm 1.0 meter M14x1.5 No No No
2114/40/00/1/10 11mm 180mils 100 40mm 5mm 1.0 meter M14x1.5 Yes No No
2118/50/00/1/10 18mm 6mm 2.5v/mm 50mm 5mm 1.0 meter 7/8-14 Yes No No
2119/50/00/1/10 18mm 6mm 2.5v/mm 50mm 5mm 1.0 meter M20x1.5 Yes No No
2125/50/00/1/10 25.4mm 13.5mm 0.8v/mm 50mm 5mm 1.0 meter 1-1/4x12 Yes No No
2126/50/00/1/10 25.4mm 13.5mm 0.8v/mm 50mm 5mm 1.0 meter M30x1.5 Yes No No
2127/76/00/1/10 25.4mm 13.5mm 0.8v/mm 76mm 0 1.0 meter N/A Yes No Yes
2150/50/00/1/10 50mm 26mm 0.4v/mm 50mm 0 1.0 meter 1-12 Yes No No
2151/50/00/1/10 50mm 26mm 0.4v/mm 50mm 0 1.0 meter M24x1.5 Yes No No
219X Series Advanced Design Probes
Probe Range Sensitivity Body Length Non-Thread Probe/Cable Thread Size Armour Rev. Right
Part Number Tip Dia. (mV/mil) “B“ Dim Length “C“ Length”E” Cable Mount Angle
Dim Dim
2197/40/00/1/10 8mm 80mils 200 40mm 0 1.0 meter M10x1 No No No
2198/40/00/1/10 8mm 80mils 200 40mm 0 1.0 meter M10x1 Yes No No
2195/40/00/1/10 8mm 80mils 200 40mm 0 1.0 meter 3/8-24 No No No
2196/40/00/1/10 8mm 80mils 200 40mm 0 1.0 meter 3/8-24 Yes No No
2100 Series Standard Probe Drivers
Probe System Target
Part Number Tip Dia. Length
2108/5/001 5/8mm 5.0m 4140 (SCM440)
2108/9/001 5/8mm 9.0m 4140 (SCM440)
2111/5/001 11mm 5.0m 4140 (SCM440)
2111/9/001 11mm 9.0m 4140 (SCM440)
2118/5/001 18mm 5.0m 4140 (SCM440)
2118/9/001 18mm 9.0m 4140 (SCM440)
2125/5/001 25mm 5.ECOL Motors
WE MOVE WHEN
OTHERS STOP
COMPANY BRIEF INTRODUCTION
Shanghai Top Motor Co., Ltd., one of leading motor manufacturers in China with a famous brand,
TECHTOP, specializes in production and sale of electrical produces, which are electric motors conformed
to IEC, NEMA, GOST standard, permanent magnet motor, water pumps, generators, generating sets and
the likes. The company has obtained ISO9001 Certificate and its products have Certificates of CSA, UL,
CE, CCC etc..
TECHTOP warmly welcomes cooperation with the customers all over the world and provides the
best-quality products and most sincere service to the friends.
WORKSHOP & TECHNOLOGY
TECHTOP adopts computerized machine tools for metal parts; four cylinder oil hydraulic presses
for stator stacking; vacuum high-pressure vanishing units for stator vanishing; clean-dry and
auto-phosphorescing machines for motor housing, end shield, fan cover and other parts;
electrostatic spraying-water screen-suspending line complexes for product surface painting.
www.motor-techtop.com
6
ECOL MOTORS
1
M otor Spare Part List "Exploded Drawing"
M ountings and Positions
1. Screw
2. Gasket
3. Oil seal
4. Front endshield
5. B14 fl ange
6. B5 fl ange
7. TB cover
8. TB fi xing screws
9. TB upper gasket
10. Terminal board fi xing nut
11. Terminal bridge
12. Terminal pin
13. Terminal shim
14. Terminal board
15. TB fi xing screws
16. TB base
17. Cable gland
18. TB bottomgasket
19. Frame
20. Preload washer
21. Key
22. Rotor
23. Bearing
24. NDE endshield
25. Cooling fan
26. Fan circlip
27. Fan cover
28. Fan cover fi xing shim
29. Fan cover fi xing screws
30. Endshield fi xing nut
31. Rivet
32. Nameplate
33. Foot fi xing nut
34. Foot fi xing screws
35. Foot
Mountings and positions for standard motors, according to IEC 60034-7,
are defi ned by the codes mentioned in the following table.
CONNECTION DIAGRAM
V1 IM V1 IM 3011 Standard
V3 IM V3 IM 3031 Upon request
V5 IM V5 IM 1011 Upon request
V1/V5 IM V15 IM 2011 Upon request
Standards
CEI 2-14 IEC 60034-7
Frame Sizes
56-200
B3 IM B3 IM 1001 Standard
B3/B5 IM B35 IM 2001 Standard
B5 IM B5 IM 3001 Standard
B14 IM B14 IM 4001 Standard
B8 IM B8 IM 1071 Upon request
B6 IM B6 IM 1051 Upon request
B7 IM B7 IM 1061 Upon request
Standards
CEI 2-14 IEC 60034-7
Code I Code II Code I Code II
Frame Sizes
56-200
V6 IM 1031 Upon request IM V6
This catalogue is only a reference for users.
The concrete data be changed please contact with us before ordering.
W2 U 2 V2
U 1 V1 W1
Y ?
U
W2 U2 V 2
1 V1 W1
PTC
1
2
P
P
2
3
AC
(L)
E
P
F
G
D
T
M N
4-S
HD
L
AC
TBW
E
R
T
N
TBS F
G
D
TBH
P
M
S
HD
Overall & Installation Dimensions
Frame Foot Mounting Shaft General
H A B C D E F G K AA AD HD AC L TBS TBW TBH
80 80 125 100 50 Ф19 40 6 15.5 Ф9 160 220 140 Ф158 280 16 97 97
90S/L 90 140 100/125 56 Ф24 50 8 20 Ф10 175 240 150 Ф176 325/350 16 97 97
100 100 160 140 63 Ф28 60 8 24 Ф12 200 265 165 Ф199 388 20 118 118
112 112 190 140 70 Ф28 60 8 24 Ф12 230 291 179 Ф220 405 29 118 118
132S/M 132 216 140/178 89 Ф38 80 10 33 Ф12 255 332 200 Ф259 467/505 29 118 118
160M/L 160 254 210/254 108 Ф42 110 12 37 Ф15 314 402 242 Ф313 605/650 91 162 187
180M/L 180 279 241/279 121 Ф48 110 14 42.5 Ф15 348 439 259 Ф360 687/725 160/180 162 187
200L 200 318 305 133 Ф55 110 16 49 Ф19 388 497 297 Ф399 768 192 186 233
225S 4,8 225 356 286 149 Ф60 140 18 53 Ф19 436 553 328 Ф465 814 190 186 233
225M 2 225 356 311 149 Ф55 110 16 49 Ф19 436 553 328 Ф465 809 202 186 233
4,6,8 225 356 311 149 Ф60 140 18 53 Ф19 436 553 328 Ф465 839 202 186 233
250M 2 250 406 349 168 Ф60 140 18 53 Ф24 484 616 366 Ф506 918 233 218 260
4,6,8 250 406 349 168 Ф65 140 18 58 Ф24 484 616 366 Ф506 918
984/1035
984/1035
233 218 260
280S/M 2 280 457 368/419 190 Ф65 140 18 58 Ф24 557 668 388 Ф559 265 218 260
4,6,8 280 457 368/419 190 Ф75 140 20 67.5 Ф24 557 668 388 Ф559 265 218 260
315S 2 315 508 406 216 Ф65 140 18 58 Ф28 630 840 525 Ф680 1160 130 350 430
4,6,8 315 508 406 216 Ф80 170 22 71 Ф28 630 840 525 Ф680 1190 130 350 430
315M/L 2 315 508 457/508 216 Ф65 140 18 58 Ф28 630 840 525 Ф680 1310 130 350 430
4,6,8 315 508 457/508 216 Ф80 170 22 71 Ф28 630 840 525 Ф680 1340 130 350 430
355M/L 2 355 610 560/630 254 Ф75 140 20 67.5 Ф28 740 920 565 Ф820 1770 180 350 430
4,6,8 355 610 560/630 254 Ф95 170 25 86 Ф28 740 920 565 Ф820 1840 180 350 430
Bearings
Cable Gland Oil Seal
Drive End Non-Drive End Drive End Non-Drive End
6204ZZ
6205ZZ
6206ZZ
6306ZZ
6308ZZ
6309C3
6311C3
6312C3
1-M20×1.5
1-M20×1.5
1-M20×1.5
2-M25×1.5
2-M25×1.5
2-M32×1.5
2-M32×1.5
2-M40×1.5
6313C3 2-M50×1.5
6314C3 2-M50×1.5
6316C3 2-M50×1.5
2-M63×1.5
2-M63×1.5 6319C3
6317C3
NU319
NU322
6319C3
6322C3
20x34x7
25x37x7
30x44x7
30x44x7
40x58x7
45x65x8
55x72x8
60x80x8
65x90x10
65x90x10
65x90x10
70x95x10
70x95x10
80x100x10
80x100x10
85x110x12
95x120x12
95x120x12
110x140x12
20x34x7
25x37x7(20x34x7)
30x44x7
30x44x7
40x58x7
45x65x8
55x72x8
60x80x8
65x90x10
65x90x10
65x90x10
70x95x10
70x95x10
80x100x10
80x100x10
85x110x12
95x120x12
95x120x12
110x140x12
IM B5 3 IM B14 4
4
Model Power
(KW)
Full Load Speed
(r/min)
Inl 400V
(A)
Ifl 400V
(A)
Ist /In
(Times)
Eff.
100%FL
(%)
Power Factor
(CosΦ)
Full Load Torque
(N.M)
Tst /Tn
(Times)
Tmin/Tn
(Times)
Tmax /Tn
(Times)
2 Pole - 3000 rpm Synchronous Speed 50Hz
T1A 801-2 0.75 2838 1.09 2.06 5 72.1 0.73 2.52 2.2 1.9 2.6
T1A 802-2 1.1 2836 1.54 2.90 5 75 0.73 3.70 2.2 1.8 2.6
T1A 90S-2 1.5 2842 1.98 3.79 5 77.2 0.74 5.04 2.2 1.8 2.5
T1A 90L-2 2.2 2835 2.39 5.04 5.5 79.7 0.79 7.41 2.2 1.8 2.5
T1A 100L-2 3 2841 2.97 6.56 5.5 81.5 0.81 10.08 2.3 1.9 2.6
T1A 112M-2 4 2900 3.88 8.58 6 83.1 0.81 13.17 2.4 1.9 2.6
T1A 132S1-2 5.5 2895 4.65 11.16 6 84.7 0.84 18.14 2.3 2 2.6
T1A 132S2-2 7.5 2900 5.98 14.81 6.4 86 0.85 24.70 2.3 2 2.7
T1C 160M1-2 11 2910 7.85 20.83 6.3 87.6 0.87 36.10 2.3 2 2.7
T1C 160M2-2 15 2908 10.57 28.06 6.8 88.7 0.87 49.26 2.3 2 2.7
T1C 160L-2 18.5 2912 11.69 33.60 7 89.3 0.89 60.67 2.3 2 2.7
T1C 180M-2 22 2920 13.81 39.69 7.2 89.9 0.89 71.95 2.3 2 2.6
T1C 200L1-2 30 2915 18.67 53.64 7 90.7 0.89 98.28 2.3 2 2.6
T1C 200L2-2 37 2920 22.90 65.80 7.2 91.2 0.89 121.00 2.3 2 2.7
T1C 225M-2 45 2920 26.21 78.70 7 91.7 0.90 147.16 2.3 2 2.7
T1C 250M-2 55 2930 35.47 97.85 7.8 92.2 0.88 179.25 2.2 1.9 2.5
T1C 280S-2 75 2930 45.66 131.22 7.8 92.7 0.89 244.44 2.1 1.9 2.5
T1C 280M-2 90 2930 51.68 155.21 7.7 93 0.90 293.32 2.1 1.9 2.5
T1C 315S-2 110 2940 62.97 189.09 7.7 93.3 0.90 357.29 2 1.8 2.3
T1C 315M-2 132 2940 71.12 223.93 7.6 93.5 0.91 428.74 2 1.8 2.3
T1C 315L1-2 160 2945 91.10 273.57 7.8 93.8 0.90 518.81 2 1.8 2.3
T1C 315L2-2 200 2945 120.08 345.07 7.9 94 0.89 648.51 2 1.8 2.3
T1C 355M-2 250 2945 142.04 426.54 7.8 94 0.90 810.64 2 1.8 2.3
T1C 355L-2 315 2945 189.13 543.48 7.8 94 0.89 1021.40 2 1.8 2.3
4 Pole - 1500 rpm Synchronous Speed 50Hz
T1A 802-4 0.75 1410 1.03 2.00 5.4 72.1 0.75 5.08 2.2 1.9 2.6
T1A 90S-4 1.1 1415 1.32 2.71 5.3 75 0.78 7.42 2.2 1.8 2.6
T1A 90L-4 1.5 1410 1.74 3.60 5.5 77.2 0.78 10.16 2.2 1.8 2.5
T1A 100L1-4 2.2 1420 2.31 4.98 6 79.7 0.80 14.79 2.2 1.8 2.5
T1A 100L2-4 3 1420 3.08 6.64 6 81.5 0.80 20.17 2.3 1.9 2.6
T1A 112M-4 4 1425 3.74 8.47 6.3 83.1 0.82 26.81 2.4 1.9 2.6
T1A 132S-4 5.5 1420 4.85 11.29 6.5 84.7 0.83 36.99 2.3 2 2.6
T1A 132M-4 7.5 1420 5.98 14.81 6.4 86 0.85 50.44 2.3 2 2.7
T1C 160M-4 11 1430 8.61 21.32 6.8 87.6 0.85 73.46 2.3 2 2.7
T1C 160L-4 15 1435 10.06 27.74 6.7 88.7 0.88 99.82 2.3 2 2.7
T1C 180M-4 18.5 1435 12.32 33.98 7.2 89.3 0.88 123.11 2.3 2 2.7
IE1 Effi ciency Motors Technical Data
5
IE1 Effi ciency Motors Technical Data
Model Power
(KW)
Full Load Speed
(r/min)
Inl 400V
(A)
Ifl 400V
(A)
Ist /In
(Times)
Eff.
100%FL
(%)
Power Factor
(CosΦ)
Full Load Torque
(N.M)
Tst /Tn
(Times)
Tmin/Tn
(Times)
Tmax /Tn
(Times)
T1C 180L-4 22 1450 15.29 40.60 7.3 89.9 0.87 144.89 2.3 2 2.6
T1C 200L-4 30 1450 18.67 53.64 7.6 90.7 0.89 197.57 2.3 2 2.6
T1C 225S-4 37 1460 22.90 65.80 7.5 91.2 0.89 242.00 2.3 2 2.7
T1C 225M-4 45 1470 29.18 80.49 7.3 91.7 0.88 292.33 2.3 2 2.7
T1C 250M-4 55 1470 33.70 96.85 7.4 92.1 0.89 357.29 2.2 1.9 2.5
T1C 280S-4 75 1470 48.11 132.71 7.5 92.7 0.88 487.21 2.1 1.9 2.5
T1C 280M-4 90 1470 51.68 155.21 7.7 93 0.90 584.65 2.1 1.9 2.5
T1C 315S-4 110 1475 62.97 189.09 7.8 93.3 0.90 712.15 2 1.8 2.3
T1C 315M-4 132 1475 71.12 223.93 7.8 93.5 0.91 854.58 2 1.8 2.3
T1C 315L1-4 160 1475 85.93 270.56 7.9 93.8 0.91 1035.86 2 1.8 2.3
T1C 315L2-4 200 1475 113.63 341.23 7.7 94 0.90 1294.82 2 1.8 2.3
T1C 355M-4 250 1475 150.10 431.33 7.9 94 0.89 1618.52 2 1.8 2.3
T1C 355L-4 315 1475 178.97 537.44 7.8 94 0.90 2039.34 2 1.8 2.3
6 Pole - 1000 rpm Synchronous Speed 50Hz
T1A 90S-6 0.75 930 1.16 2.15 5.3 70 0.72 7.70 2.2 1.9 2.6
T1A 90L-6 1.1 930 1.63 3.02 5 72.9 0.72 11.29 2.2 1.8 2.6
T1A 100L-6 1.5 935 2.09 3.94 4.9 75.2 0.73 15.32 2.2 1.8 2.5
T1A 112M-6 2.2 935 2.97 5.60 5.7 77.7 0.73 22.47 2.2 1.8 2.5
T1A 132S-6 3 935 3.95 7.44 6.3 79.7 0.73 30.64 2.3 1.9 2.6
T1A 132M1-6 4 940 5.01 9.59 6.2 81.4 0.74 40.64 2.4 1.9 2.6
T1A 132M2-6 5.5 940 6.34 12.57 6.8 83.1 0.76 55.87 2.3 2 2.6
T1C 160M-6 7.5 950 8.49 16.82 7 84.7 0.76 75.39 2.3 2 2.7
T1C 160L-6 11 955 11.43 23.56 7.3 86.4 0.78 109.99 2.3 2 2.7
T1C 180L-6 15 955 14.84 31.25 7.2 87.7 0.79 149.99 2.3 2 2.7
T1C 200L1-6 18.5 960 15.58 36.31 6.9 88.6 0.83 184.02 2.3 2 2.7
T1C 200L2-6 22 960 18.41 42.89 7.3 89.2 0.83 218.84 2.3 2 2.6
T1C 225M-6 30 970 24.82 57.84 7.4 90.2 0.83 295.34 2.3 2 2.6
T1C 250M-6 37 970 27.94 69.20 7.5 90.8 0.85 364.25 2.3 2 2.7
T1C 280S-6 45 975 32.26 82.63 7.7 91.4 0.86 440.74 2.3 2 2.7
T1C 280M1-6 55 975 37.40 99.29 7.7 91.9 0.87 538.68 2.2 1.9 2.5
T1C 315S-6 75 975 45.71 131.36 7.9 92.6 0.89 734.56 2.1 1.9 2.5
T1C 315M-6 90 975 51.74 155.37 8 92.9 0.90 881.47 2 1.8 2.3
T1C 315L1-6 110 975 62.97 189.09 7.7 93.3 0.90 1077.36 2 1.8 2.3
T1C 315L2-6 132 975 79.68 228.96 .8 93.5 0.89 1292.83 2 1.8 2.3
T1C 355M1-6 160 975 85.93 270.56 7.6 93.8 0.91 1567.06 2 1.8 2.3
T1C 355M2-6 200 975 113.63 341.23 7.8 94 0.90 1958.83 2 1.8 2.3
T1C 355L-6 250 975 150.10 431.33 7.8 94 0.89 2448.54 2 1.8 2.3
6
Model Power
(KW)
Full Load Speed
(r/min)
Inl 400V
(A)
Ifl 400V
(A)
Ist /In
(Times)
Eff.
100%FL
(%)
Power Factor
(CosΦ)
Full Load Torque
(N.M)
Tst /Tn
(Times)
Tmin/Tn
(Times)
Tmax /Tn
(Times)
2 Pole - 3000 rpm Synchronous Speed 50Hz
T2A 801-2 0.75 2848 0.96 1.86 6 77.4 0.75 2.51 2.7 2.1 2.8
T2A 802-2 1.1 2846 1.20 2.52 6.7 79.6 0.79 3.69 2.7 2.1 2.9
T2A 90S-2 1.5 2852 1.32 3.17 6.1 81.3 0.84 5.02 2.3 2 2.7
T2A 90L-2 2.2 2845 1.89 4.54 7 83.2 0.84 7.38 2.6 2.1 2.7
T2A 100L-2 3 2851 2.00 5.75 7.6 84.6 0.89 10.05 2.5 2 2.8
T2A 112M-2 4 2910 2.63 7.56 7.8 85.8 0.89 13.13 2.5 2 2.7
T2A 132S1-2 5.5 2905 3.57 10.25 7.8 87 0.89 18.08 2.4 2 2.9
T2A 132S2-2 7.5 2910 5.06 13.96 7.9 88.1 0.88 24.61 2.7 2 2.8
T2C 160M1-2 11 2920 6.57 19.73 7.9 89.4 0.90 35.97 2.2 2.1 3
T2C 160M2-2 15 2918 8.37 26.35 7.9 90.3 0.91 49.09 2.3 2.1 3
T2C 160L-2 18.5 2922 9.64 31.93 8 90.9 0.92 60.46 2.4 2.1 2.9
T2C 180M-2 22 2930 13.60 39.08 7.5 91.3 0.89 71.70 2.3 2 2.8
T2C 200L1-2 30 2925 19.39 53.49 6.7 92 0.88 97.94 2.4 2 2.7
T2C 200L2-2 37 2930 21.36 64.15 6.3 92.5 0.90 120.59 2.3 2 2.7
T2C 225M-2 45 2930 28.81 79.45 6.9 92.9 0.88 146.66 2.3 2 2.8
T2C 250M-2 55 2940 35.09 96.80 8 93.2 0.88 178.64 2.3 1.9 2.7
T2C 280S-2 75 2940 37.86 125.45 8 93.8 0.92 243.60 2.2 1.9 2.7
T2C 280M-2 90 2940 45.28 150.06 7.7 94.1 0.92 292.33 2.2 1.9 2.6
T2C 315S-2 110 2940 62.30 187.08 7.7 94.3 0.90 357.29 2 1.8 2.3
T2C 315M-2 132 2940 70.29 221.33 7.6 94.6 0.91 428.74 2 1.8 2.3
T2C 315L1-2 160 2945 90.14 270.68 7.8 94.8 0.90 518.81 2 1.8 2.3
T2C 315L2-2 200 2945 118.82 341.44 7.9 95 0.89 648.51 2 1.8 2.3